Set Filter Cycle Duration
Press SET button until TOOLS is displayed:
Press TEMP UP button
Press SET button until FILT1 is displayed:
Press TEMP UP button
Press TEMP UP or TEMP DOWN to set Filter Cycle 1 duration
Press SET button until FILT2 is displayed:
Press TEMP UP button
Press TEMP UP or TEMP DOWN to set Filter Cycle 1 duration
Press SET button until EXIT is displayed:
Press TEMP UP button to exit
The Absolute Best Hot Tub Ownership Experience
No matter which model you select, you can count on superior quality, comprehensive warranties and outstanding customer care from our experienced dealers.
Committed to our Customers
Our dedication to high-quality construction and unparalleled customer care means you can enjoy your Hot Spring spa for years to come. You can count on support from our network of experienced and professional retailers and our straightforward warranties to ensure your spa is always running at its best.
THOUGHTFUL DESIGN
Hot Spot Spas feature attractive shell and cabinet designs that will integrate beautifully into your backyard. Colorful lighting and soothing waterfalls add to the fun.
SIMPLE AND STUNNING
With quality craftsmanship that only comes from Hot Spring Spas, Hot Spot model owners will enjoy the benefits of spa ownership for years to come. All Hot Spot Spas feature the following:
- Stylishly sculpted, comfortable shells
Filter Cycles & Heating Modes
- Two filter cycles per day
- First filter cycle starts 10 minutes after power-on
- Second filter cycle starts 12 hours later
- Filter cycle duration programmable 0 to 6 hours
IMPORTANT: “Tranquil Mode” disables heating and filtration cycles for 10 minutes after high-speed jets are turned off. Pressing the Jet button to activate low speed will override Tranquil Mode and start a heating cycle if the temperature control is calling for heat.
Don’t Miss: How To Get Rid Of Springtails In Pool
Instructions On Filling Your New Hot Spring Hot Spot Hot Tub For The First Time:
Starting up your new Hot Spring Hot Spot Series hot tub is not as overwhelming as it might seem. We realize you may see conflicting information, especially if you are getting tips and advice from the Internet. Its important to remember that not all hot tubs are made to function in the same manner, so please call your salesperson if you have any questions about starting up your hot tub for the first time.If you have well water we strongly recommend using a pre-filter attachment on your water hose to reduce and eliminate problematic minerals from entering your hot tub. Please take the time to read thru the following instructions before starting to fill your new spa and refer to the section below, Hot Tub Water Care Guide, for how to properly balance your new spas water!
- Do not fill the spa with hot water, as tripping of the high-limit thermostat may result.
- DO NOT CONNECT POWER TO AN EMPTY SPA. Power to the spa automatically activates critical components within the spa, such as controls, heater, and other systems. If power is supplied to these components prior to the spa being filled, the components will be damaged, and this may result in a non-warranty component failure.
- Do not use your spa after filling until all of the steps listed below are completed.
- Before filling your spa for the first time, remove the equipment compartment door and check to ensure that the unions on either side of the pump and heater are hand-tight.
Hot Tub Water Care Guide For Hot Spring Hot Spot Spa Customers:
Balancing your hot tub water should not begin until your spa is heated to the desired temperature. As your water heats up, pH and Alkaline levels may change, so its important not to rush through the startup process. Once your hot tub has achieved the desired temperature, you may test the spa water for the first time with your test strips. Simply dip the test strip in the water and then pull the strip out of the water and line up the colored pads on the strip to the back of the bottle. Make a note of what your readings are before adding any chemicals to the water. Ideally, your spas pH should read between 7.2-7.6 ppm and the Alkaline should be between 80-120 ppm.
A few things to remember
You May Like: How To Open Pool After Winter
Page 2: Common Water Chemistry Questions