How To Lower The Ph In Your Hot Tub
Typically, the active ingredient in pH decreaser, sodium bisulfate, will also lower TA, sometimes so significantly youll need to bump your TA back up a little afterward.
Sodium bisulfate also helps stabilize pH, so if you do need to tweak your TA, its less likely to become an endless pH rollercoaster ride.
Muriatic acid is an alternative way to decrease both pH and alkalinity. Because its an extremely caustic chemical, you must use safety glasses, chemical-resistant gloves and a whole lotta caution when working with it. Heres more information on lowering hot tub alkalinity.
To be even safer, you can use a muriatic acid replacement product thats not as caustic. Youll still need to wear the safety gear, though.
Its not the best idea to just pour muriatic acid directly into your spa. Youll need to dilute it, add it to your spa, then aerate it by running the jets. Finally, leave your spa to circulate overnight before retesting the water.
Does Epsom Salt Lower Ph In Water
Yes, Epsom salt can lower the pH in water but it should not be used in a hot tub that already had chlorine in it.
You can only use Epsom salt with plain water for your own health and the safety of the spa components.
Using Epsom salt can lead to the build-up of Total Dissolved Substances which is not safe for your hot tub.
Repeat The Process Or Drain And Refill The Hot Tub Completely
If your pH and alkalinity levels werent too far off to begin with, you might be done with the process of raising the pH in your hot tub! However, you may still have a bit farther to go. If levels are close to where they should be, go ahead and repeat the process.
But in the case that alkalinity and pH levels are still far from the ideal range, it may be best to completely drain out your hot tub and refill it. Sometimes, its easier to start fresh, rather than continuing to add chemicals over and over again in hopes that you will be successful. For best results, use a hose filter like the Fresh Start® Clean Screen when refilling your hot tub in order to keep contaminants out. Using a metal sequestrant is also helpful for filtering out any metal build-up in the hot tub.
Don’t Miss: How To Clean Pool Sand Filter
Did I Cover Everything You Wanted To Know About Whether Its Safe To Use A Hot Tub When The Ph Is Too High
In this article, we took a look at the pH of hot tubs and how high is too high.
We examined what happens when the pH gets too high, and what to do when it does. We also looked at the urban myth of whether baking soda can lower the pH.
Specifically, though, we answered the question of can you use a hot tub if the pH is high? The answer to that question is, of course, it depends on how high the pH is.
But if the pH is over 7.8 on your test strip, its best to NOT use it until youve balanced the water chemistry.
How Do You Balance Ph In A Hot Tub
Most hot tub owners find it difficult to balance the pH or total dissolved solids of their hot tub after use or when contaminants bloom. Many others struggle with this issue almost every day, even when it is not used.
This could be as a result of the different water quality they have. The bad news is that there is not much you can do to change the quality of water from your source. The good news is that there is so much you can do to change the chemistry of the water without struggling. All you need is just simple knowledge and a little patience.
Let us study some basic pH scenarios and how to settle the issue:
The main reason why total alkalinity was added is that a change in total alkalinity would definitely affect the pH level of the water. The main range of alkalinity should be between 80 and 120 parts per million. pH should be 7.4 to 7.8 ppm, with 7.5 being the best point.
You May Like: What Is The Best Metal Frame Pool To Buy
How To Lower Hot Tub Ph
How to Lower Hot Tub pH
Hot tubs do require a certain degree of maintenance and keeping the water properly balanced and sanitary is one of the most important routine tasks that an owner needs to stay on top of. When the water in a hot tub becomes unbalanced or too alkaline, the water conditions quickly deteriorate. When the water becomes too alkaline, the pH level increases and you will need an acid chemical that will be capable of lowering both the pH and alkalinity.
To learn more about what steps you need to take to maintain the proper balance of your hot tubwater and how to lower the pH level, keep reading below.
Selecting the Proper Chemicals
In order to lower both the pH and alkalinity of your hot tub water, you will need to add acid. Common choices are liquid muriatic acid or dry sodium bisulfate. When the acid is introduced to the water, it increases the hydrogen concentration and lowers the pH. The acid also reacts with the bicarbonate in the water which is what reduces the alkalinity.
Check Your Measurements
When you are trying to balance your water, it is important to remember that the pH drops faster than the alkalinity, so if you correct the alkalinity first, the pH level will slowly adjust. While each chemical brand or type is different, typically you need approximately 1.23 litres of muriatic acid for every 10,000 gallons of hot tub water. This measurement will drop the total alkalinity by 10 ppm.
Mixing the Chemicals
Adding to Hot Tub
LetBalance
What Reduces Foam In A Hot Tub
Foam in your hot tub can be one of the most confusing things to get rid of, especially when you do not know the cause. The first step to removing foam from a hot tub is knowing what started it.
That is why you test the water for any imbalance and know whether it is too much or too low. In most cases, just adding an extra pH increaser or decreasing bromine or chlorine would do the magic. While doing this, make sure your hot tub filter is cleaned thoroughly to remove potential contaminants.
Note that if the filter is dirty and you are trying to solve any issue in the hot tub, lurking contaminants from the filter will make the newly added chemicals ineffective.
If the foam remains persistent after checking and treating the water, make sure you start afresh by draining the water, washing, and rinsing the tub.
Use a clean hose to refill, test, and add chemicals to balance the water chemistry while making sure the hot tub jet is on for quick circulation of the chemicals.
Wait for at least 24 hours, retest, make sure all the water properties are balanced, especially if that was the cause, and then you can use the hot tub.
Read Also: Orlando Hotels With The Best Pools
How To Add Alkaline Water To Your Hot Tub
Adding alkaline water to your hot tub can help to improve the overall pH balance and provide a more relaxing soak. There are a few things youll need before you get started: an alkaline water filter, carbon filters for the pump and circulation system, and pH test strips.
- 1. Fill your hot tub with enough fresh water to cover the solids. If using tap water, make sure it is filtered through an alkaline water filter before adding it to the tub.
- 2. Insert the carbon filters into the pump and circulation system. These filters will help remove chlorine and other pollutants from the incoming water.
- 3. Add pH test strips to each end of the pool so you can monitor the acidity level throughout your soak.
- 4. Add the bath salts to the water and remove any clumps that form so they dissolve completely in your soak.
- 5. Set your timer for 15 minutes, then add another 15 minutes of soaking time.
- 6. Rinse off the bath salts and ring the water out of the tub with a hose.
- 7. Add your favorite oils, lotion, or potions, and enjoy your soak!
What Is Ph And Why Is It Important
So once you have balanced your TA, the next step is to use a test kit or strips to check your PH level. PH is the measure of how acidic or how alkaline your water is. 7 is the neutral PH level but in your hot tub you want to aim to get your PH between 7.2 and 7.8. If you do not do this you may in for some nasty and potentially costly suprises!
Also Check: What Chemicals Do I Put In My Intex Pool
What Happens When Ph Is Too Low
Low pH levels in your hot tub mean that the hot tub water is acidic. Acidic water can cause a lot of damage, both to the hot tub and your health.
When your hot tub pH becomes low, the water can cause corrosion on your hot tub components and surfaces. If the issue is not corrected, the corrosion can lead to cloudy water.
Moreover, the acidic water can sting your eyes and dry your skin causing itchy dry skin. You will also feel a burning sensation in your nose. These experiences are not good for anyone, especially people with respiratory health challenges.
How To Lower Ph In A Hot Tub
wikiHow is a wiki, similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 9 people, some anonymous, worked to edit and improve it over time.There are 7 references cited in this article, which can be found at the bottom of the page. This article has been viewed 291,002 times.Learn more…
When the water in a hot tub becomes too alkaline, its pH increases, and the condition of the water deteriorates significantly. The total alkalinity of the water will probably be high at this point, as well. To lower the pH in a hot tub, you need to add a pool acid capable of dropping both the pH and total alkalinity.
Also Check: Aluminum Above Ground Pool Deck
Why Is The Ph So High In My Hot Tub
There are different factors that could be responsible for the increase of pH levels in your hot tub. What comes to our mind when the pH rises is that we have added excess chemicals, probably when we were trying to balance the water chemistry.
Well, that is true, but not always the case. There are other things that can alter the pH of your spa water. The major ones include
- Excess amount of pH Increaser
- Serbia and organic matters
It is possible that you might have added an excessive amount of the pH Plus you use which resulted in the abnormal increase in pH levels.
But if you have adjusted the pH levels recently, then the problem could be from your local water supplier. Try to test the pH and alkalinity of the water you are using in your hot tub. There are chances that they are high.
If thats not the case, then its time you start thinking of how to clean up your hot tub, whether by draining or without draining. The presence of algae could be responsible for the increase in pH.
Thats right, algae can alter the level of your spa water pH when it consumes the carbon dioxide in it. As the carbon dioxide depletes, the water becomes more alkaline resulting in an increased pH level.
What Are Ph Levels
PH levels measure acidity and alkalinity in water on a pH scale. A pH scale is numbered from 0-14 a measurement of 7 is considered neutral or balanced.
A Ph level between 7.2 and 7.8 should be maintained in your hot tub.
7.2 or below indicates that your water is too acidic, which can cause itchiness and eye burn, and your sanitiser to be less effective. High acidity can result in costly damage to your hot tub parts too.
7.8 or above, like high alkalinity, can contribute to scale build-up, foam and cloudy water.
Keeping your pH levels in check creates a more comfortable environment for your bathers, avoids scale and calcium build-up, and will keep your tub free from corrosion.
You May Like: When Do Pools Open Up
How To Bring The Ph Down In A Hot Tub
It is worth mentioning that there’s no almighty formula for lowering the pH level in a hot tub. This is because hot tubs are different from each other, and they require different levels of maintenance and chemicals. Also, different factors can affect the frequency of chemically balancing your hot tub, the number of chemicals to add, and the level of maintenance.
The main factors that affect the chemicals and amount of maintenance include:
- The quality and source of water
- Cleanliness of bathers
- Water temperature
- Hot tub maintenance interval and quality
You’ll need acid to lower both the pH and alkalinity of your hot tub. The most commonly used acids are sodium bisulfate and liquid muriatic acid. The pH lowering mechanisms are the following:
- Hydrogen ions: When mixed with water, the acid lowers the pH by increasing the concentration of hydrogen ions
- Bicarbonates: Also, the acids reduce the total alkalinity by reacting with bicarbonates in the water.
Using Sodium Bisulfate To Lower The Hot Tub Ph
Sodium bisulfate is a lot safer than muriatic acid, but a more expensive option. The acid is mostly available in the granular form because the dry acid is mild. Sodium bisulfate is also a great pH lowering agent that you can use in your hot tub. However, you’ll need to exercise some level of caution when using this acid.
Here’s how you can use sodium bisulfate to bring down the pH in your hot tub:
Read Also: Which Zodiac Pool Cleaner Is Best
Harm From Low Ph Levels
If the water in the hot tub isacidic, things can go wrong quickly. The acid will etch or corrode any metal itcontacts. The heater is made of metal, as are many of the fittings. The hot tubwalls may crack or delaminate. Sanitizers will be less effective.
The peopleusing the hot tub will also notice itchy and dry skin, as well as irritatedeyes. While the pH in a hot tub will rarely,if ever, get to dangerous levels, itchiness and irritation take away from theenjoyment of the hot tub. Low pH may also harm your bathing suits as the acidwears away the fabric.
Chlorineis crucial to keeping the water in a hot tub safe. Chorine works best in a slightly acid environment. Its effectiveness is at 97%, witha pH of 6. That level of acidity, however, would lead to the itchy skin and eyeirritation noted previously.
It isworth noting that everything which goes into the water will affect the pHlevel, including the humans enjoying the hot tub. The pH of human skin is 5.5, which means we lower the pH ofthe hot tub each time we enjoy it.
How To Lower Ph Levels Without Chemicals
To lower the pH level of your hot tub water, you can take four cups of vinegar and pour it in the water. Remember to circulate the water in the tub before you pour in the vinegar. You can either use the vinegar you have at home or use apple cider vinegar. Turn off the jets and test the water after a few hours. Till you get an appropriate level, repeat the process.
Proper maintenance of your hot tub will extend the life span of your hot tub, and you will kick back, relax, and enjoy your time submerged in your spa.
Don’t Miss: How Do I Make My Pool Salt Water
What Happens If The Hot Tub Ph Is Too Low
If a hot tub pH is too low, the water is acidic. This can lead to the corrosion of equipment and surfaces. It also makes it difficult to adjust the alkalinity. Acidic water is uncomfortable because it irritates the eyes and removes natural oils from the skin, rendering it dry and itchy.
It can also cause the breakdown of swimwear and hot tub accessories.
Low pH may also lead to rapid dissipation of chlorine, requiring that you use more. What are the causes and remedies?
The water in your area may be naturally more acidic, or perhaps your hot tub is often uncovered, and rainwater has fallen into it.
The water may also have become imbalanced because of improper use of sanitizers and other hot tub chemicals. If you use too much chlorine, it could decrease the hot tubs pH and make the water more acidic.
The following are methods for raising the pH of your hot tub:
- UseBaking Natrium hidroksida
Ill get into baking kaustik soda below. But my favorite product for raising the pH in a hot tub isLeisure Time Spa Up on Amazon.Just click that link to check the current price on Amazon.
Woo Hoo Today is Bubble Bath Day: A good day to soak in a hot tub! What is your go to for a perfect bath? I prefer no bubbles2 cups of Epson salts, 1/2 cup baking soda, tablespoon of almond oil and 5 drops of lavender E.Udara murni. Im dreaming of a good soak~Sabrina pic.twitter.com/WZW7TdCU7e
New Mix 100.7 January 9, 2019
