Wednesday, June 15, 2022
HomeCleanHow To Clean Pool Filter Cartridge

How To Clean Pool Filter Cartridge

- Advertisment -

Dip The Pool Filters In Tsp Cleaner Solution

How To Clean a Pool Filter Cartridge

Use approximately 1 cup of TSP every 5 gallons of water in a bucket . About two pounds worth. If possible, leave the filters submerged overnight .

Adding one cup of dishwashing to five gallons of water can also be used, but keep in mind that dishwasher detergent is not the same as dishwashing detergent . Many dishwasher detergents are primarily TSP alternatives since they are made to produce less foam.

Rinse the filters afterward to eliminate any loose particles.

Types Of Cartridge Filters

There are several different types of cartridge filter housings. The pictures used in this article are for a basic capsule-style housing. Some may have band clamps in the center, others may have wing nuts on the top, and some even have a series of small cartridges. The cartridge cleaning procedure itself is the same.

How To Clean Pool Filter Cartridge

Cartridge filters, like Hayward, are the most widely used type of pool filter because theyre efficient and straightforward to maintain. Theyre also more eco-friendly because they require less water use during the cleaning process.

A cartridge filter works by pumping the pool water through a cylindrical filter cartridge made of pleated polyester fabric. The fabric traps particles in the water and catches smaller particles than other pool filters.

When it comes to how to clean pool filter cartridge fabric, there are various approaches. Choosing one depends on how dirty the filter is and the supplies you have available.

  • Filter cleaning solution

Turn off the pool pump at the breaker, then drain the air from the system using the pumps air relief valve, normally at the top of the filter.

Remove the top of the filter. Consult your owners manual to ensure that you dont accidentally damage the filter housing.

After removing the pool filter cartridge, closely inspect it for any signs of cracking, tears, or other damage. If the filter is damaged, it needs replacing.

Check the o-ring on the filter tank, too. Replace it if you notice any cracks, dry rot, or warping. Otherwise, apply a non-petroleum-based lubricant to keep it from drying out before your next cleaning.

Read Also: High Iron In Pool Water

How To Deep Clean A Pool Or Spa Filter Cartridge

If you suspect that your swimming poolor spa cartridge filter isnt running as efficiently as it should be or you seethat your pool or spa is cloudy all of the time then it may be time to cleanyour filter cartridge.

Cartridge Renu is a product that getsthe cleaning process done quickly and efficiently. This solution can be usedwith both DE filter grids and filter cartridges. It works extremely well ingetting rid of body oils, grease, soap film, DE, dirt, other organics, andgeneral gunk that tend to clog filter system and reduce their efficiencies.

Cartridge Renu is a blend of degreasersand cleaning agents that are specially formulated to penetrate deeply into anyreusable cartridge filter or DE element and remove any materials that haveaccumulated. Giving the cartridge a thorough rinse and soak allows it to beused again. Regular cleanings will help extend the lifespan of the cartridge.

To use Cartridge Renu, youll want touse a plastic or rubber container that is large enough to submerge the entirefilter and allow it to soak. The appropriate proportion of solution is 4 ouncesof Cartridge Renu for every 1 gallon of water.

When the cartridge is out and being rinsed,its also a good time to do a visual inspection. If the filter looks good youcan place the cartridge back in the filter and resume filtration as is needed.

Five: Rinse The Filter Off

How To Clean A Cartridge Filter

Before you begin to clean the filter, you need to see what you are working with. Take the hose and spray the big chunks off the filter. Spray the water at an angle to the pleats on the filter to help lift the gunk off. However, if you have the filter cartridge cleaner tool, put it on your hose and use this to get right into the pleats.

Also Check: Pool Hours Mandalay Bay

Sign Up For The Poolstyle E

Receive the latest design trends, hot products, special offers, and more!

Cleaning your filter cartridge is fairly simple, and you dont need any special tools or cleaning solutions for removing debris — in fact, the only thing you need is access to a hose. It should only take about a half hour to complete this 10-step process:

  • Turn off the power to your pool pump. This is always important when working with electricity, but its especially critical if your filtration system runs on an automatic timer.
  • Open the valves on the filter. The air relief valve releases the pressure, and the ball valve drain the water from the filter.
  • Remove the lid from the tank. Yours might have a lock ring, clamp, or knob, depending on your model.
  • Remove the cartridge from the filter canister. A gentle rocking motion while lifting up might help to dislodge the filter elements.
  • Set it down in a good spot for cleaning. Remember, youll end up with debris like decomposed leaves, silt, and fibers, so choose someplace that makes it easy to scoop up afterwards.
  • Inspect the cartridge for damage. Before cleaning, look for cracks, tears, or other damage. Even a small tear will decrease your filters performance.
  • Hose off the cartridge.
  • Use moderate pressure from a regular garden hose .
  • Hold the hose at a 45-degree angle to avoid damaging the filter.
  • Spray off the cartridge from the top down until the debris is gone.
  • Flip over the cartridge and repeat the spray from the other direction.
  • Instructions For Cleaning Your Filter Cartridge

    All cartridge filters should be cleaned at least every 1-2 months . If you follow these cleaning procedures you will ensure the maximum life of the cartridge:

    • Remove the cartridge from the filter housing or skimmer box.
    • Wash the filter using a garden hose or a cleaning tool, working from the top down. Do not use a high pressure hose or a brush.
    • Soak the cartridge for at least an hour in a cartridge cleaning solution which you can purchase from your local Spa & Pool shop. Alternatively, use 1 cup of a household detergent in 5 litres of water to clean.
    • Rinse the cartridge once more with a hose to remove any remaining oils or cleaning solution.

    Eventually your cartridge filter will block and will need to be replaced usually within 1 to 2 years depending on the amount of use.

    Opening Hours Mon Sat: 8:00am 5:00 pm

    Glenfield

    Read Also: Aria Pool Cabana Review

    When Do I Know Its Time To Replace My Filter Cartridge

    You can use a few different methods to determine when to replace your cartridge filter.

    If you notice that your pool is producing murky water even after cleaning the pool and filter, it is likely time to replace the filter.

    If you have cleaned the filter thoroughly and soaked it in cleaner and muriatic acid and the filter cartridge is still full of debris and mineral build up, this is another indication that it may be time to throw the old one out and buy a new one.

    Keep in mind that the filter will need replacing every 3-5 years, so it is normal to purchase a new one once in a while.

    What Other Solutions Can I Soak A Pool Filter In

    How To Clean A Pool Filter Cartridge

    You can make your very own solution using good old dish soap. To do this you will need to add a cup of liquid dish soap to at least 5 gallons of water. Then allow your pool filter to soak for as long as you wish.

    We heavily advise against soaking your pool filter in bleach as this can damage the cartridge material reducing its lifespan.

    Recommended Reading: Homemade Swimming Pools

    What Is A Cartridge Filter

    An essential part of a swimming pool is the pool filter which makes the water clean from dirt and pollution.

    Among the different types of pool filters, a cartridge filter is becoming popular for its easy maintenance and durability. Cartridge filters are effective at removing particles, germs, insects, and more. But it also needs to be maintained properly to ensure clean water for swimming in a pool.

    Imagine if you are cleaning your house with a dirty mop which itself needs to be cleaned. You are not cleaning it or making it worse. Just like that, your filter should be cleaned properly to keep the pool water clean and safe.

    If the pool filters become dirty and clogged, they can build up chemicals bacteria and can make the water cloudy. So, a clean filter is necessary.

    Remove The Cartridge From The Tank

    Once you have the clamp off, carefully pull the top section off your filter tank. Depending on the make and model of filter, it may contain a single large cartridge element or up to four smaller ones. Remove all of them, and set them aside to be cleaned.

    Most units with one large cartridge will lift right out of the tank without unfastening any attachments. Smaller filters may have elements with attachments that hold them in place. Refer to the owners manual for instructions on removal.

    Also Check: Tibbets Park Pool Yonkers Ny

    Degrease Or Deep Clean The Cartridge

    Hosing and the other methods described above will remove large debris from the cartridge. However, these strategies are not always enough to handle stickier substances like algae, sweat, sunscreen, and body oils that seep into the cartridge materialand interfere with its efficiency.

    If your pool and spa get a lot of use with swimmers bringing in these kinds of bather wastes , its a good practice to periodically perform a deeper cleaning. This extra step will provide a more thorough removal of dirt and debris and help maintain the filters effectiveness.

    The most common way to achieve good results is with a commercial pool degreaser or cartridge cleaner . These are available at hardware stores, pool supply stores, and online.

    To use, spray the product directly onto the cartridge. Be sure to cover all of the surface areas between the pleats. Leave the compound on for the recommended amount of time. Then, thoroughly rinse it off with a hose. If the buildup on the cartridges is particularly dense and nasty, consider soaking them overnight.

    There is no hard-and-fast rule here regarding frequency. Some pool owners deep clean every other timewhich may mean only once per year when pool and spa use is high. Others will examine the filter materials to see if material seems sticky or coated, and only if it is, will they use a degreaser.

    Can I Clean Pool Filter Cartridge With Bleach

    How to clean Hayward pool filters or cartridge pool filters without any ...

    To remove a stain from a piece of clothing, you might soak it in bleach, so does that mean that you can soak your cartridge in bleach? Companies that sell pool chemicals advise against doing so, since bleach can damage the fibers of your filters and thereby shorten your filter life.

    Cartridge manufacturers offer a range of products to help keep your filters clean. Some pool owners make cleaning solutions out of detergents or vinegar which are more gentle on your filters over time.

    Don’t Miss: Will A Sand Filter Remove Iron From Pool Water

    Clean A Pool Cartridge Filter: Step By Step

    The role of your pool filter is to capture small pieces of debris floating in pool water and screen them out. Over time, dirt builds up in the cartridge elements, and it needs to be cleared out.

    First, determine if your filter needs to be cleaned. When the filter gauge shows that the PSI is more than 8 to 10 PSI higher than whats normal for your filter, its time for some housekeeping.

    Hint: You can check your owners manual for the correct PSI range, but the best approach is to know whats normal for your pool when operating with its specific features and equipment configuration. To obtain this baseline, check the PSI when the cartridge is brand new or right after you have performed a deep cleaning on it. .

    To clean your cartridges, follow the simple steps outlined here. Also included are some tips for avoiding pitfalls and making the job as easy as possible.

    How To Clean Your Filter

  • Turn off your pump. For safety reasons, if you are using an automated system, turn off your pool at the mains power. If the pump suddenly turns on while your fingers are inside the filter component, you could get hurt.
  • Remove the filter element. This is located inside the filter housing check the product manual for specific guidelines.
  • Clean the debris. Dont rush this step thoroughly rinse the filter inside and out between the pleats with a garden hose. Products like the Water Wand save time by cleaning between the crevasses of eight pleats at a time.
  • Blow-dry the element. Once the element is dry, use compressed air to remove small dirt particles.
  • Degrease. This step is the premium car wash option and is not necessary unless you want optimal performance from your pool filter. If you choose to use a degreaser every time you clean your cartridge, you will guarantee your filters effectiveness and lifespan. Soaking the cartridge in an approved cleaning solution will remove body fats, sunscreen, and other oils.
  • You May Like: Aria Cabana Prices

    Pool Filter Cartridges: When To Clean And When To Replace

    Proper cleaning of your filter cartridges will not only help to keep your pool as clean as possible, but also increase its useful life.

    Eventually, the cartridge will have to be replaced. Dirt, oils and minerals build up which cleaning wont remove.

    Here are some tips for when/how to clean a pool filter cartridge, and when to replace your pool filter cartridge.

    How To Clean A Hayward Pool Filter

    How To: Clean a Pool Cartridge Filter

    Cleaning a Hayward pool filter is not an easy task. We are here to help you and make the process a bit easier. You dont have to spend a fortune on new filters to keep your pool running at its best. Continue reading and learn how! These steps also apply to any pleated cartridge pool filter. You can use this guide on cleaning any filter used in a hot tub or Jacuzzi.

    Contents

    Also Check: Pool Tile Grout Sealer

    How To Clean Swimming Pool Cartridge Filters In Easy Steps

      Tips and guidelines for smart filter housekeeping to help ensure efficient filtration

      Keeping your swimming pool water looking and feeling good requires regular cleaning of your pool filter. Fortunately, for those with a cartridge-type filter system, maintaining the elementsthe tubes of folded, accordion-like material that goes inside the filter tankis easy to do.

      Why Are Filters Necessary

      Though it might seem like an obvious chore, cleaning your pool, and realizing the importance of doing so, is often overlooked by homeowners. For starters, unkept pools and filters can lead to more serious backyard problems down the road, and can ultimately cause more homeowners more money.

      A clean pool is also essential for you and your familys health. The cleaner your pool water, the less likely it is to contain parasites, waterborne illnesses and bacterias. The same applies to the environment. If your pool becomes dirty or contaminated, you run the risk of letting dirty water seep into your neighborhoods waterways and environment.

      Don’t Miss: Chlorine For Intex Pools

      Homemade Pool Cartridge Filter Cleaner

      Sunscreen and body oils are challenging to remove from your pool filter cartridge. However, using a stiff-bristled brush on your cartridge filter to remove contaminants may damage the polyester or paper pleats.

      To remove stubborn residue, be sure to use a soft-bristled brush designed explicitly for cleaning cartridge filters to avoid accidentally ruining the cartridge.

      Instead of purchasing expensive chemicals, try making your own DIY filter cleaning solution.

      • 4 gallons water
      • 5-gallon bucket

      In a five-gallon bucket, blend the ingredients and submerge your filter cartridge in the cleaning solution. Soak for three to ten hours. After soaking, rinse the cartridge before reassembling the filtration system.

      Always check your filters maintenance manual and warranty information before using DIY cleaning products to ensure that you wont damage the product or void the warranty.

      When Is It Time To Replace Your Entire Filter System

      Ultimate Guide to Cleaning Your Pool Filter (HOW TO STEP BY STEP)

      There will also come a time when you need to replace the entire pool filter pump system. Such equipment has a life expectancy of 8-12 years, provided that it has been well-serviced.

      Some signs that you need to replace the entire pump are:

      • The filter spits out an alarming amount of bubbles due to several cracks and air leaks in the equipment.
      • The filter makes grinding, screeching, rumbling sounds or quick, repetitive pops. Pool filter systems should be quiet.
      • The water is constantly cloudy or green, and youre having a tough time maintaining a good pH balance even though the cartridge is new and the pressure gauge is reporting a healthy and consistent amount of pressure.

      As a top tip, before opting for a complete replacement, call a pool expert to see if these problems are repairable.

      Read Also: How To Use Black Hose To Heat Pool

      Test The Filters Air Pressure

      With the pump running, open the filters air relief valve to release any excess air in the system. When water consistently sprays out of the valve, there is no more air in the system. Check the filter pressure to make sure its falling within the proper range for your filter when its clean.

      Additional cartridge maintenance tips

      Taking The Filter Out Of The Filtration System

    • 1Remove the filter when the pressure is 7-10 lbs above normal. The operation pressure of your filtration system will increase when the filters are dirty because the pumps are having a harder time pushing water through the filters. This higher pressure on your gauges is a great indicator of when its time to clean the filters.XResearch source
    • There are cases when the pressure wont increase even though the filter is dirty, such as if there is a hole in the filter that water can easily flow through. However, in most cases, high pressure is a good sign that your filter needs cleaning.
    • Unless your pool gets very dirty, very often, this should only occur once or twice a year.
    • 2Turn off the pool pump and water supply to the system. Locate the main electrical breaker for the pool filter system and turn it to the off position. Then locate the water supply disconnect and turn it to the off position as well.XResearch source
    • Turning these off before you remove your filter will ensure that water will drain from the filter compartment and that there will be no risk of shock while you are cleaning out your filter.
    • 3Release the air relief valve to depressurize the filter system. Once the water is turned off, you can release the system pressure by turning the pressure valve. The valve is usually located on top of the filter compartment or near to it. Releasing this valve will allow the water to drain from the filter compartment before you take the lid off.XResearch source
    • Read Also: Lice Chlorine Pool Water

      RELATED ARTICLES
      - Advertisment -

      Most Popular

      - Advertisment -