How To Replace Pool Motor

How To Replace Pool Motor Bearings

Pool pump motor bearing replacement. Most local electric motor repair shops will be glad to replace your motor bearings. Replacing your bearings as an alternative to replacing the motor, , can save a lot of money. Consider this:

1. Replace Entire Pump: $400-6002. Replace Pump Motor: $200-4003. Rebuild Pump Motor: $125-1754. Do it Yourself: Priceless;

S To Replacing Noisy Pump Motor Bearings

1. Shut off power at the breaker. Remove motor from pump housing. Remove wiring harness from rear of motor.

2. Remove pump diffuser. Hold shaft at rear of motor with pliers/wrench, and spin impeller off shaft, counter-clockwise.

3. Lubricate 4 through-bolts with WD-40. Gently loosen and remove through-bolts. Mark or make a scratch across end bell and body of motor to line up later.

4. Use a flathead screw driver and small hammer to loosen and pry off the front end bell .

5. If entire rotor does not come out, pry off the rear end bell.

6. Clean the bearings and look closely at the bearing number. Look for 202, 203, 303 or 304. Buy these at a motor shop, or online pool motor parts.

7. Using bearing pullers, pull off the old bearings. Clean the shaft and use a tamping tool, or a piece of pvc pipe to help set the bearing in place on the shaft.

8. Reassemble the rotor into the stator, secure the end bells in the marked or scored positions made earlier, and tighten down the through-bolts.

9. Reassemble the impeller, wear ring , reverse threaded impeller screw , diffuser and wiring to rear of motor.

10. Test motor wiring by turning motor on briefly. Reinstall the motor into the pump, fill with water, and enjoy the new silence!

Pool Pump Repair Cost

Repairing a pool pump can sometimes cost less than replacing it. This cost is $50 to $200, depending on the exact part that needs repairing. The most common problems that homeowners face are pool pump leaks, the pump not pulling water through the system, the pump only pulling in air, motor failure, or the pump producing weird noises. All these require the attention of a professional, especially if the pump is less than five years old.

Recommended Reading: Can Lice Live In Chlorine Pools

When To Replace A Pool Pump

There are 2 major parts to a pool pump: the motor mechanism and the pump mechanism. Each one may fail and will need your attention. Some indicators that its time to replace a pool pump includes complete motor failure, the motor making a loud grinding or screeching noises, the pump no longer moves water or its leaking water.

Remove The Rear Bearing First

Setup the bearing puller on the rear bearing. The “teeth” of the puller should be positioned on the outside ring of the bearing to clear the retainer clip on the back. It goes without saying that the center post of the bearing puller should be aligned with the motor shaft. Turn the nut on the bearing puller to work the bearing off of the shaft. Once the bearing is off, check the id/model number stamped into the back side of the bearing. make sure that this matches the new bearing that you have bought.

Recommended Reading: How To Heat An Above Ground Pool

Hayward Pool Pump Cost

Haywards pool pumps are in the middle of the price range of these products, going between $500 and $1,200. They sell a wide variety of pool pumps, from industry-standard single-speed pumps to energy-efficient variable-speed pumps so that they can be installed on different types of pools. Most of Haywards products are energy-star rated, ensuring high energy efficiency while providing high flow with lower HP.

S To Finding The Correct Gokit Or Shaft Seal

Most popular pumps have a gasket and O-ring kit, aka GOKIT, associated with them. A GOKIT is a complete set of seals used for a specific pump model. The kit consists of the lid, seal plate, and diffuser gaskets as well as the shaft seal. This kit is a great add-on to a motor purchase because it allows you to replace all the pumps seals in one go since the pump is already disassembled.;There are two styles of GOKITs: the standard and the heavy-duty version. These two kits are the same except for the shaft seal. The saltwater kit includes a GOKIT and is not required to complete a motor installation, but the shaft seal is.For me, the most important part of the motor installation is the shaft seal. That little two-sided seal is the last line of defense keeping the water in your pump and away from your brand new electric motor. Using an old shaft seal when installing a new motor is a guaranteed premature motor failure .

Step 1: Take a picture of your pumps model number

Take a picture of your pumps profile and any labels that look like they contain information about the make and model.

Step 2: Visit InyoPools.coms pool pump parts page;

Go to Inyos pool pump parts page to start your search. There are a couple of ways you can begin your search.

Method 1 Use the pumps model numberIf your pump has an easily identifiable model number, you can enter it into Inyos search feature to view the parts diagram.

Method 2 Match using our pump picture lineup sorted by manufacturer

Also Check: How To Get Out Of Contract With Blue World Pools

How To Fix Leaking Pool Pump

Watch the full video on how to fix the leaking Pentair Challenger pool pump:

The pool pump shaft seal on our neighborhood pool started leaking tons of water. The pool pump housing is a Pentair Challenger mated to a large strainer basket. The pump motor we are using is a Century Centurion Model B1000

The motor shaft diameter is 5/8in

Pentair Challenger Pool Pump seal kit

Leslie’s Pool Supply Repair Kit #65005

Shaft Viton Pump Seal Part PS200V Leslie’s Part #40677

Buy from Amazon – https://amzn.to/3ydEVGq

Diffuser O-ring Leslie’s Part # 66518

Buy from Amazon – https://amzn.to/382tpD8

Housing Gasket Leslie’s Part # 608185

Buy from Amazon – https://amzn.to/3D8kyOu or https://amzn.to/3B1RhDp

Strainer Basket Gasket Leslie’s Part # 44562

Buy from Amazon – https://amzn.to/3japsm4

After replacing all the seals and gaskets on the pump, the pool pump motor ended up also needing its bearings replaced because water had gotten past the multiple seals and into the bearing. The motor is a Century Centurion B1000. It was impossible to find out what size bearings were used. None of the pool companies knew, and I also contacted the manufacture, which led me to their local service center, who spent some time looking for documentation that had the bearing sizes, and they could not find it either. Finally, the bearings seized, the pump motor stopped, and we had to remove and take it apart to determine the bearing dimensions.

Should I Repair Or Replace My Pool Pump Motor Or The Whole Pump

This ultimate question depends on how the damage occurred and if you caught the issue in time.

Mechanical wear and tear can be complicated, especially for swimming pool pumps that operate outdoors and have very essential moving parts. It takes a qualified technician to check your pool pump for issues and to properly diagnose the problem.

Thats why Select Home Warranty offers home warranties on swimming pools and spas, including the pumping system, filtration system and heating system. When you experience a mechanical breakdown, you can place a claim which covers repairs and replacements covered under your terms of service.

Dont spend your summer wishing your pool was operating and get ahead of pool pump breakdowns with a home warranty instead.

Sign up today for your free quote on optional pool coverage to keep your pool open all season long! Select is here to shield your home and your wallet from costly breakdowns.

Read Also: How To Deter Wasps From Pool

The Pool Pump Is Leaking Water

In most cases, a leak underneath a pool pump is caused by a pressure-side leak. This is easily combated by inspecting the impeller housing o-ring, shaft seal and replacing any worn, cracked o-rings or seals. Before taking apart your pool pump, we recommend purchasing a go-kit. It is relatively inexpensive and will have all the necessary parts to replace your worn o-rings and seals.

How Do You Replace Pool Motor Bearings

How to Replace Pool Motor Bearings

. Likewise, people ask, how much does it cost to replace pool pump bearings?

With the cost of parts at roughly $30 , a bearing job can be an inexpensive fix. A caveat: It’s not uncommon for a bearing replacement to last less than a year.

Likewise, how do you know if your pool pump motor is bad? common pump problems andquick fixes

Also question is, how much does it cost to replace a pool motor?

Pump Or Motor ReplacementSimply replacing the motor is less expensive than replacing the entire pool pump. A DIY motor replacement costs approximately $25 to $200, while hiring a pro may cost an additional $40 to $100.

How do you fix a noisy pool pump motor?

How To Troubleshoot a Pool Pump Motor – Motor Noisy

How to Quiet a Noisy Pool Pump

You May Like: Can Lice Live In Chlorine Pools

Pool Pump Replacement Options

Traditional pool pumps utilize single-stage motors that eat up huge amounts of electricity. As reported by the;U.S. Department of Energy, the average unit consumes nearly $500 worth of electricity each year. With todays improved technology, two-stage motors and adjustable-speed units use up to 90 % less energy and function at speeds as low as 600 rpm than their traditional counterparts. They are also usually compatible with automated home systems.

How To Replace The Motor On Your Pool Pump

;3.28 out of5 stars on 174 ratings

Today’s pool pump motors are much more efficient. If you have an older pool pump or it’s motor is running loud or just stop working, you’ll want to consider replacing your pool pump motor. You do not have to replace the whole pool pump and as this guide will show, replacing your pool pump motor is not difficult. Although this guide is specific to a Hayward pool pump, most of the steps can apply to other models of pool pumps. Caution: You must ensure that the electrical supply agrees with the motor’s voltage, phase, and cycle and that all electrical wiring conforms to local codes and NEC regulations. If you are unsure of this voltage or are unfamiliar with electrical codes and regulations, have an electrician wire your pump for you. Failure to wire the pump correctly can cause electrical shock or can damage your pool pump motor and void your warranty.

You May Like: Best Sealer For Stamped Concrete Pool Deck

When To Replace Your Pool Pump & Common Problems With Solutions

When it comes to enjoying summer, theres nothing quite like relaxing beside your own pool. Thats why on these bright and sunny days, sitting by a murky pool can be a real downer.

Keeping your pool open all summer long is no easy task. Select Home Warranty offers an optional coverage plan on the mechanical components of your pool or spa, including the pumping system, filtration system and heating system.

In the event of a breakdown, well send out a technician to assess the problem, so get your free quote today or call us:;860-288-4791

One major component, the pool pump, is called the heart of your swimming pool. When this component is acting up, it can put a grinding stop to your summer fun. But how do you know if its time to replace your pool pump?

Pool Water Pump System Cost

A new pool water pump system with a timer costs between $750 and $1,550. Timers ensure that your pool doesnt run constantly and you wont have to manually turn the pump on and off. If youre adding a new filter as well, this could bump the total project costs up to $700 to $5,550. Get a project quote from a pool service near you.

Recommended Reading: Can You Heat An Above Ground Pool

The Flow Rate Of The Pool Pump Is Low

If the flow rate of the pump has dropped, you will want to make sure there is nothing blocking the flow of the pump or filter. Check your filter gauge first. If you are above 10psi over the clean reading specified by the manufacturer, youll want to clean the filter to reduce the pressure and reset the flow back to the pool pump.

Next, check your pump basket and impeller for debris that would be blocking water flow. To remove the impeller, turn the power off to the pump and remove the screws in the middle of the pump body. Once the screws have been removed, pull the assembly out of the housing and remove the gasket away from the impeller, remove any debris and re-assemble.

How To Replace Your Pool Pump Motor

A pool can be a fantastic feature to have in your yard. It can be the source of endless fun and a place where priceless memories are made. To keep your pool fun and safe, you need to maintain it properly. An inground pool pump plays an essential role in pool maintenance. Its what circulates the water throughout your pool so it can be filtered and sanitized. While newer pump motors are designed to be more efficient and last longer, they eventually wear out.; At some point, youll inevitably need to replace your pool pump01 motor.

You May Like: Head Lice Swimming Pools

How To Replace A Swimming Pool Pump Seal

wikiHow is a wiki, similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 13 people, some anonymous, worked to edit and improve it over time. This article has been viewed 243,250 times.

Leaking pumps can destroy the swimming pool motor. Here is some advice on how to replace a pool pump seal. The following instructions are general. Seal components are similar for most centrifugal pumps.

Insert And Connect The New Pump

Remove the cover to the motor, and connect the electrical wires to the new pump the same way that they were connected to the old pump. Attach all the plumbing connections and tighten them. Once all the plumbing and electrical connections are completed, the pool pump is ready to be turned on and primed.

Read Also: How To Remove Limescale From Pool Tiles

Biggest Mistakes When Replacing A Pool Motor

I talk to thousands of customers each year about replacing their pool pump motors and the vast majority of our customers install the motors themselves without a hitch. However, occasionally we do encounter mistakes which are made when replacing your motor. So I decided to poll my fellow co-workers, manufacturers and vendors to come up with a list of the seven most common mistakes when replacing a pool motor. The results are in Drum roll please

Best Pool Pump Brands

Pool pumps are available online and at local pool stores. When searching for the best pool pumps, two brands dominate the market: Pentair and Hayward. Both companies are known for making quality, long-lasting pool pumps, and they offer a wide variety of options including single-speed, variable-speed, and energy-efficient models. Although a pool company can direct you to the pump that best fits your needs, here are a few of the popular models offered by both Pentair and Hayward:

Also Check: How Much Is Salt Water Pool

Bearing Or Motor Replacement Cost

If you have a relatively new pool pump and the pump exterior does not show any sign of deterioration, you can replace the bearing or the motor.

The older the pump, the difficult it will be to find some bearing and motor replacement parts. It will most likely be more than 75% of the cost of the full pump replacement. If that is the case, it is best just to replace the entire pump.

If you want to replace your bearing or your motor, it is less expensive than replacing the entire pump. A DIY bearing replacement can cost you about $25 to $200 while hiring a professional will cost you an additional $40 to $100.

Additional Considerations And Costs

• Maintenance. Regular pool maintenance, which includes opening and closing your pool properly, can help prolong the life of your pump.
• DIY. If you are replacing a pool pump of the same type and size, you may be able to do this project DIY. Make sure you shut off the electricity at the breaker before beginning. Remove the cover and disconnect the old pump, lift it up and disconnect the wiring. Youll install the new pump in reverse order. Wire it in first, then lower it down and connect the plumbing. However, keep in mind that having your pump installed by a professional is always the safest way of installing it.
• Energy ratings. Energy Star rated pumps are available, these are usually variable speed motor pumps that use less energy overall, so you can save. If you purchase these pumps there may be rebates or credits available to offset the cost.
• Estimates. Before picking one brand and model of a pump, get at least three estimates. This will give you a general idea of the pricing of pool pumps and allow you to understand what is offered in each price range, ultimately helping you make a better decision.
• Warranty. Some pool pumps come with a warranty for a specific time that serves as a guarantee that the pump will function properly for the time.

Don’t Miss: Doheny Sand Filter System