How To Maintain A Cement Inground Pool
A cement inground pool is basically just a large hole dug into the ground with a concrete shell to contain water. A vinyl lining is permanently attached to the concrete shell to give the inside of the pool a smooth feel. The operation of an inground concrete pool is no different than that of an above-ground pool: Both have a filtration system that circulates the water and keeps it clean and free from debris. Inground pools require routine maintenance, surface cleaning, and chemical additives to stay in good operating condition.
1
Use a pool skimmer to remove any floating debris from the surface of the water.
2
Clean the sides of the pool by scrubbing them with a plastic-bristle pool brush. Work your way around the entire pool moving the brush in a circular motion.
3
Wait 10 minutes after scrubbing the sides of the pool for any dirt or small particles to settle on the bottom of the pool. Vacuum the bottom of the pool by slowly moving a pool vacuum across it. Move the pool vacuum very slowly and in straight lines to avoid stirring up any dirt or debris settled on the bottom of the pool. Brushing and vacuuming should be performed weekly to keep the pool clean.
4
Add the correct amount of algaecide to the pool once a week. The typical algaecide dosage is 3 oz. per 10,000 gallons of water, but refer to the manufacturer’s instructions for the exact amount.
5
6
7
Clean out any filtration traps around the pool at least once a week.
8
References
Test And Balance The Water
Make sure the chemical balance of your pool water is at its optimal level. This way, youll know precisely how much pool shock to use. Use either a liquid test kit or test strips. Dont worry about calcium hardnessfocus on pH, alkalinity, and sanitizer.
Heres where the levels should be:
- alkalinity: 100 ppm to 150 ppm
- pH: 7.4 to 7.6
- chlorine: 1 ppm to 3 ppm
How to Raise pH in Pool
If you find out the pH level of your pool is low, there are a couple of things you can do to raise it:
- Add Soda ASH: Soda ash or sodium bicarbonate have lots of alkalinity, easily dissolve in water, and dont leave much of a trace. Adding either of them will decrease acidity and raise pH levels of your pool water.
- Aerate The Water: This can be done by pointing water jets towards the pool surface, by turning on water features, or adding aeration pipes. However, doing this is a lengthy process, and can take days.
How To Acid Wash A Concrete Pool
STEP 1: DRAIN & CLEAN With a main drain in the pool and a multiport valve on the filter, you can drain most of the pool water with your filter pump, but it will lose prime with 1-3 feet of water still in the deep end. You can use a submersible pump to finish the job, like the Water Wizard, which fits in a main drain pot. For bad pool clean-ups however, go to your local rental shop at 7 am, and rent a 2 or 3 Trash Pump, with a 20 long suction hose, to reach the main drain, and as much discharge hose as you need, 50 or 100 usually. Stop at the gas station and fill up a gas can for refueling.
As you drain the pool, wash it down to remove all algae and leaves. If you let the algae dry on the surface, it becomes twice as difficult to remove. Spray the surface with a water nozzle as the water level drops, before it dries into a baked-on finish. When all of the water is removed, bag up all leaves and debris in the pool’s bottom. Rinse again, remove the main drain cover so that you can pump out all of the water, to begin acid washing the bowl, or the area around the main drain.
When the pool is clean and completely empty, you can begin to acid wash the plaster, in the deep end. Put on protective clothing and rubber boots, goggles and wear a breathing mask designed for acid fumes.
Read Also: Does Costco Sell Pool Chlorine
Best Ways To Clean A Concrete Patio
If you enjoy low-maintenance solutions, youll be happy to know that cleaning sealed concrete floors is much easier than cleaning unsealed ones. In this article, we show you simple but successful ways to clean a concrete patio so that youll never again be stumped about how to clean a concrete patio.
With a few household cleaning products in easy DIY combinations, youll soon have a patio so clean that youll want to break out the patio chairs and fire up the barbeque.
How To Clean Concrete Pool Deck
Concretes are well-known material when it comes to pool decks. And are very good material to consider when thinking of a swimming pool deck. They are available in different colors and they resist outdoor elements. They are also a great slip-resistant material, so they are the best choice for pool decks.
Is your pool looking very dirty? Or you are not satisfied with the look of your pool. And you feel it is dirty and it needs cleaning. And you need some steps to follow to give you what you want. This article will give you the steps to follow on how to clean concrete pool deck area.
You May Like: Are Variable Speed Pool Pumps Worth It
Uses For Concrete Pool Decks
When first introduces in the 1970s, there were very few choices of designs and colors of stamped concrete. However, as the industry grew, more stamping patterns along with different types of stains, were created, giving endless design possibilities for this material. A concrete pool deck can come in a variety of shapes and sizes depending on your desires, budget, and existing pool area. These areas make the perfect oasis for relaxing on lawn chairs, patio furniture, and beach areas. Stamped concrete also makes the ideal place to set up a barbecue or fire pit for everyday entertainment.;However, once installed, it is important to keep up with proper maintenance.
Does Pool Chlorine Kill Mold
There is a common misconception among people.
A pool chlorine cleaner doesnt clean the concrete driveway.
Thats not true. With pool chlorine, we can guarantee you will find proper results. Its just as effective as a bleach solution, which is really effective when it comes to killing mold on patios and driveways.
Recommended Reading: How Much Is Salt Water Pool
Cement Pool Maintenance Conclusion
Whether you need help with installation, pool repairs, or quality pool service in Gulf Coast, Premier Pools & Spas of Gulf Coast professionals has your needs covered. Well help maintain the right levels of chemicals and pH and clean the swimming pool as necessary. Just call us to schedule a consultation and well find the level of care thats right for your budget and your pool.
Quadruple Shock The Pool
Youre going to quadruple shock your pool because a regular dose wont be enough. See what the manufacturer says is the correct dose for your pools volume, and then multiply that by four.
Use calcium hypochlorite because nothing else on the market works as good as this substance for getting rid of black algae. Place all your pool maintenance equipment, such as the brush, the leaf skimmer, and the tablet holder, in the shallow end so it can be sanitized while youre shocking your pool.
Remember to do your shocking at night. If you do it during the day, the suns rays will neutralize the chlorine before it has a chance to kill the bacteria.
You May Like: How To Vacuum Intex Above Ground Pool
How To Clean Concrete
JoyfulNoise said:Bleach and trisodium phosphate will get rid of mildew/mold/algae. You apply it using a bucket and scrub brush, let it sit and then rinse it. If the power washer left your concrete rough, then the pressure was way too high and/or the wrong fan tip was on the wand. They sell rotary spray heads that you can hook up to a power washer that are designed for hard surface cleaning. You may be able to rent one.
JoyfulNoise said:Its also a good idea to use soft water if you have it available. Calcium will react with the TSP and form insoluble phosphates and carbonates which can leave behind a powdery residue. Using soft water would eliminate that. Rinse the area you treat really well. A hose with a good strong spray should be fine but if use a power washer then make sure you dial down the pressure and use the widest fan tip you have available.
How To Clean Your Pool Deck
To clean a pool deck, you’ll need standard household bleach, dish soap, an exterior scrub brush meant for concrete, a bucket, and lots of water. Follow these steps for a quick clean:
- Fill the bucket with water and add a cup of bleach and a squirt of the dish soap. Wear gloves or use the handle of the scrub brush to mix together these materials.
- Spread the solution over the pool deck. Mix additional buckets of bleach and soap as needed, to cover your entire deck.
- Use the scrub brush and brush the deck thoroughly. Be sure to take extra time over the expansion joints, or the indented trenches between sections of concrete, as dirt and grime tend to settle into these areas.
- After scrubbing the entire deck, use a pressure washer or garden hose with a pressure nozzle and rinse the water thoroughly.
To ensure you don’t damage your property’s lawn or contaminate the pool’s water, rinse the soapy solution toward the home’s driveway and into the street. Note, too, that you don’t want to use too much bleach or soap in this mixture. These materials need to dissolve completely in the water, or they might leave a residue on the pool deck. Use even less bleach on a timber deck, to avoid drying the wood and leaving unsightly marks and spots.
Recommended Reading: Removing Scale From Pool Tile
Cleaning The Water Without Draining The Pool
Whether you have a concrete, fiberglass, or vinyl-lined pool, you can clean the pool without draining it if it is dirty but not completely swampy. So how do you know which road to take? A good rule of thumb is if you can see the bottom of the shallow end of your pool even though it has been sitting, you dont need to drain it.;
How To Clean A Cement Patio Using Muriatic Acid
If none of the other cleaning solutions have been successful, consider using muriatic acid powder. However, its important to note that contact with this strong chemical can cause skin burns or damage to your eyes, lungs, and nose lining.
If you do use muriatic acid to remove mineral deposits or mold from your concrete patio, make sure to wear protective gear, including goggles and a face mask. Muriatic acid is readily available at many home improvement and big-box stores.
To prepare your cleaning solution, carefully pour one part muriatic acid into four parts hot water and stir to combine. Pour the acid over your patio and let it sit there for about ten minutes, making sure to rinse away the acid before it dries. Finish by sprinkling baking soda to neutralize any remaining acid.
You May Like: How Does The Intex Pool Vacuum Work
Use A Sealant To Protect Your Concrete
Using a sealant is beneficial for any concrete surface, but is especially important for pool deck surfaces because of the increased exposure to water and other elements. Unprotected concrete stains easily and is prone to surface damage and physical deterioration.
Nature can cause stains from moss, mold, algae, leaves or simply a buildup of deeply seated dirt. Then there are the typical man-made stains that can occur from contaminants like oil and fertilizer. Regardless of the cause of the stain, these ugly spots and patches drastically affect how concrete looks and the overall appearance of the property.
Surface pitting and physical deterioration – or spalling – is another common problem where one or many areas of the concrete surface are peeling or flaking away. Spalling is created – and accelerated – with the freeze/thaw cycle. Moisture is absorbed into the concrete and, as temperatures drop, freezes and expands, breaking the walls of the concrete surface pores. Once that damage occurs, the surface area exposed to future damage increases – meaning the effects of the freeze/thaw cycle worsen exponentially every year.
Using a concrete sealant goes hand-in-hand with pressure washing, and should be part of your annual maintenance regiment – whether as a DIY project or hiring a contractor. Not only will you instantly improve the beauty of your pool deck, but you’ll help protect and extend the lifespan of your concrete by controlling water seepage and preventing damage.
How Often To Clean A Concrete Pool Deck
Proper pool deck maintenance requires a very thorough clean once or twice a yearthe frequency of major cleans depends on several factors such as:
- How often its used.
- Whether it gets of lots of debris from nearby trees and plants.
- If dirt is often tracked onto its surface.
- Frequency of animals leaving their droppings on the deck.
Youll have a sense for how often you need to clean it based on how it looks and how difficult it is to do your thorough cleanings.
Don’t Miss: How Long Should My Pool Pump Run
How To Clean A Concrete Patio Using A Power Washer
In case youre not familiar with them, a pressure washer is a machine that releases a high-pressure stream of water, while a power washer does the same thing but specifically using hot water. These machines are invaluable for cleaning large surfaces, such as a concrete patio or the facade of a building.
The good news is that its possible to rent a pressure washer if you think youll only use it once or twice each year. To make your cleaning solution, pour one gallon of hot water into a bucket and stir in baking soda a little bit at a time, making sure that it dissolves properly.
Add some dish soap and one quart of bleach, stirring slowly so that the mixture does not overflow. Pour your homemade cleaner into the power washer and follow the instructions on the package.
Whats It Doing In My Pool
If youre recently taken a dip in the ocean, a lake, or other natural body of water and then jumped into your pool, youre at risk of introducing black algae to it. From chic bathing suits to swim-happy pets, black algae has a whole host of vehicles it can use to hitch a ride to your backyard swimming hole. Its way easier to transfer from a pond or lake than you probably ever realized.
A black algae infestation can happen if someone uses a pool float in a lake or the ocean without spraying it off thoroughly with a garden hose. The aquatic pest can even get into your pool if airborne spores of the species happen to be wafting your way .
You May Like: Aria Las Vegas Pool
Milliard 14 Inches Flexible Pool Vacuum Head
If you want to enjoy your pool time, then you have to vacuum it regularly. The best pool vacuum head makes cleaning the swimming pool easy. The Milliard flexible pool vacuum fulfills the cleaning tasks easily and in a simple way. This 14 inches pool vacuum comes with a handle adapter that you can connect with any extension pole.
This vacuum head has another amazing feature that is spring locking clips which are easy to remove and even adjust to fix with the pole.
Furthermore, the head is made of a flexible plastic surface that bends to the floor of the pool in maintaining suction on the surface being cleaned. This quality makes this device quite strong and durable.
- Width of cleaning surface:
The vacuum head is best for cleaning all types of dust and debris from your pool. Its cleaning surface is 14 inches wide and can easily clean your whole pool in less time. While the surface is triangular so it can fit in all corners and stiff spaces of your pool.;
- Vacuum head weight:
This vacuum head has a weight that keeps it at the bottom of the pool. This ability prevents you from floating back up as you clean. There are wheels under this device which make it easy to move in the water.
- Final Thoughts:
Milliard-14inches Flexible Pool Vacuum Head is undoubtedly the easiest maintaining pool vacuum head. It consistently cleans your pool and makes your pool sparkly. The large leaves are difficult to pick up but this device picks all debris from deep end corners. It is recommended.
Using Chlorine To Clean Driveway: Moving On With The Cleaning Process
The following steps will reveal the answer to your question: how to clean stained concrete driveway. Bear with us as we take you for the ride that ends in a spotless and level driveway.
Warning!
The following steps may become boring after a while. We would advise you to power on through for the best possible results.
Don’t Miss: Where To Buy Pool Pump Capacitor
Patio Furniture Cleaning 101
Since most patio furniture is either wooden, plastic, or metal, most of the above cleaning methods will work perfectly.
But if youre looking for a universal approach, start with a light soap water solution and brush.
Scrub the frame of the furniture, using a light TSP solution or lime juice mixture for spot treatment on tough stains.
Remove any cushions on the furniture and set them aside. To clean them, handwash using a light detergent, water, and soft brush.
When youre done with;cleaning, place the cushions in a sunny spot to air dry.
