How To Measure For Inground Pool Liner

How To Measure A Basic Shape Liner

It is easier to measure a pool when it is full of water. It is best if the water is clear so you can see the break points. If the water is green and you cant see the bottom, the following instructions still apply, but you will have to feel for the breaks with the vacuum pole. If you cant feel where the breaks are, drain the pool. These instructions apply even is the pool is empty.

Things To Know Before Measuring For A New Inground Pool Liner

Unlike above ground pools, inground pools come with a lot of variables in construction which can make the task of getting a replacement inground swimming pool liner a daunting one. However, with the right knowledge and patience, properly measuring for a new inground pool liner can be a simple process.

Tara’s Tabs Vs Other Methods

Other manufacturers have methods to indicate position points on the liner. They place marks or stickers at the top of the wall. This method is not as accurate as the method Tara uses. The top of the wall can be “off” from the floor in a number of ways. To fit properly the pool liner must fit the bottom of the pool. Tara places the tabs on the bottom of the pool. Tara’s system also eliminates any human error that can occur, by incorporating the tab into the liner design. Once you use our liner tabs you’ll realize why it is the easiest and most effective system in the market.

Also Check: Sizing A Pool Pump

Measure The Length And Width In Two Spots

The process begins with measuring the length and width of the pool in at least two places. When you measure, pick two parallel locations on the short and long sides, so you have accuracy. Do this rectangular, square, and ovals. If you have an odd shape, these steps do not apply.

When you measure the pool length and width, get in the pool and measure from the liner to liner. Do not measure from the concrete or the coping on the outside of the pool. The ends of the tape measure should touch the walls of the pool.

Some people find measuring easier with string. You can get these measurements with a string that you cut to size, then measure with the tape.

Inground Pool Liner Measuring

The replacement liner installer and liner manufacturer share common goals in providing liners that conform to safety guidelines, that look good, and last a long time. Safety concerns are dealt with separately. In the following pages we will attempt to throw some light on how to measure for liners. Accuracy is the key. Precise measurements are a must. Assumptions have no place in this endeavor. DO NOT attempt to make allowances for stretch or shrinkage no matter what the season. That is the manufacturers job.

You May Like: Cap050550440rt

Measure Length And Width

In a round pool, measure straight across in two different spots to ensure accuracy. In oval pools, measure round end to round end for length, then two parallel spots on the sides for width. Measure the short and long sides of a rectangular pool in two spots each to check your results.

Rectangular Pool: Measure the short and long sides in two spots each to check your results.Round Pool: Measure straight across in two different spots to ensure accuracy.Oval Pool: Measure round end to round end for length, then two parallel spots on the sides for width.

Important: Measure inside the pool walls , and pull the measuring tape as tight as possible. Getting into the water may make this easier.

There Is A 2 Plug Included With Each Main Drain You Will Use That To Plug The Bottom Hole In Each Main Drain

How to install a pool liner with a center drain. This portion of the old swimming pool liner will be removed a little later. Replacing liner with center drain. Anti vortex drain covers are the best.

Raise the liners wall toward the top of your pool wall. To install the main drains into a vinyl pool, first remove the cover and face plate off of each main drain pot, and tape over the opening, covering the faceplate screw holes with duct tape. Move the liner into position so it aligns with the skimmer box position.

This is the center line of your oval liner. I worry about cutting the hole for the center ground drain. This is great for keeping the pool clean because the return jet can be pointed to send the water parallel with the pools wall.

Can you please tell me the best way to replace the liner in a pool that already has a center drain in it. In my opinion, having a main drain on an above ground pool is optional. Take the new liner into the pool and unroll it.

Work in bare feet inside the pool. Remove the box from your pool interior. Set your pools liner and get all the wrinkles out whatever way youtube tells you and start filling with water.

The suction power of the pool pump through the drain poses the risk of dangerous pool accidents and drowning. The pool radius from the center of the drain, then add 15 cm . Unfold the liner and spread it along the pool floor out to the edges of your pool walls.

Print bottom liner installation, NO Wrinkles! Its what we

Read Also: Can I Leave My Dolphin Pool Cleaner In The Pool

How To Measure Your Pool

• Draw a diagram of your above ground swimming pool similar to the ones below. This will aid in recording the dimensions.
• Next, use the tape measure to measure from inside wall to inside wall as pictured in the diagram below. We recommend doing this twice once at the top of the wall and once at the bottom to make sure it’s accurate.
• Record the dimensions on your diagram and use them to find the right size liner.

• If you have a differently shaped pool or more complex measurements, please feel free to contact the pool experts at LinerWorld. Were always ready to help.

Note: Multiple factors, such as bowed walls and other irregularities, can impact your pool dimensions. Always re-measure rather than relying on previous notes or old liner sizes.

Once you’ve measured your pool, you’re ready to shop for a new pool liner.

Taras Tabs Vs Other Methods

Other manufacturers have methods to indicate position points on the liner. They place marks or stickers at the top of the wall. This method is not as accurate as the method Tara uses. The top of the wall can be off from the floor in a number of ways. To fit properly the pool liner must fit the bottom of the pool. Tara places the tabs on the bottom of the pool. Taras system also eliminates any human error that can occur, by incorporating the tab into the liner design. Once you use our liner tabs youll realize why it is the easiest and most effective system in the market.

Recommended Reading: Venetian Pool Times

What Do All The Letters Mean

When learning how to measure a swimming pool liner you really need to under stand what all the letters mean. Before we begin print off a liner measurement form or scroll down to familiarize yourself with the pool layout. You will quickly notice a bunch of different letters located on different points of the pool. These letters directly relate to the different dimensions needed to make a replacement liner. All off the dimension will be needed to properly make a new liner that will fit your pool. Scroll down to see how each letter corresponds to certain length, width and depth points on your pool.

• A Overall Width

• E From Bottom Of Panel To Floor
• F Overall Depth

How To Measure For An Aboveground Pool Liner

An often-overlooked step in replacing your aboveground pool liner, measuring your pool properly will prevent undue surprises.

This is because not all pools will measure to exactly the size that a pool owner thinks they have. Secondly, installation variables can cause the walls to bow out, or bow inward.

If you are planning a replacement pool liner, take a few moments to get an accurate measurement of your pool diameter and depth. Then you can confidently place an order for your replacement pool liner and aboveground liner installation supplies.

Recommended Reading: Goplus Solar Dome Swimming Pool Heater

How To Measure Pool Liners

SwimmingPoolSteve.com is user-supported. In order to keep this resource about pools and spas available for free to all readers I earn commissions for purchases made through links on this page. For more information see the full disclaimer page. By using this website you are agreeing to the terms and conditions.Measuring a new vinyl liner for a pool is something that can be done by anyone however experience goes a long way towards getting reliable, wrinkle free installation results. Learn more about how to measure a pool liner on this page or skip to one of the following sections:

Vacuuming Out The Air Adding The Water

Once the liner is positioned properly, double check to make sure the wall is aligned with the floor by looking for diagonal wrinkles. After making adjustments, youre ready for the vacuums. With this task, selecting the proper number of pumps is the first order of business.

As a general rule, the bigger the pool, the more vacuums you want to use.

“On a smaller pool, one vacuum could work, but we recommend going with at least two,” says LOOP-LOCs Hanley. “You want to keep those vacuums running while filling the pool with water.”

Pools with added amenities and special needs need special attention at this stage, and stricter attention to details is important, according to Shea.

“If you are putting in a lot of fancy features, you are definitely going to want more than one vac to help set the liner,” Shea says. “Next, position your vacuum so that it is located centrally whenever possible, whether you are feeding it through the mouth of the skimmer, down behind the liner, and/or directly down the wall, behind the bead section.”

A best-practice method is to place the vacs in the skimmer areas, according to Hanely, though he again points out installers each have their own ways of doing things.

Once a liner is pulled down tight against the wall, you know youve gotten a proper seal. Any looseness is a sign and air is escaping somewhere. Troubleshoot these areas, and iron out any remaining wrinkles, before adding the water.

Read Also: Www Skillstepup Com

Were Ok Youre Ok And Your Pools Ok

So how are you feeling? A little overwhelmed? Or are you raring for the challenge of replacing your inground pool liner? Sometimes the best way to learn how to do something is just to jump in and do it. But dont say we didnt caution you about those measurements. They have to be absolutely accurate.

Once youve got that new liner in, though, youll be all set to go back to ignoring your liner and enjoying your pool. Or maybe now that you see just how important your liner is, and what goes into replacing it, youll have a whole new appreciation for it, and will give it a little pampering now and then.

Happy Swimming!

How And When To Replace Your Inground Pool Liner

Poor inground pool liners. Theyre so neglected. Like most of us, you probably spend the majority of your pool maintenance time balancing the water and adding chemicals, and making sure your equipment is running smoothly. And there your liner sits, holding thousands of gallons of water, being ignored every day. Its a thankless job.

Eventually, your liner will go on strike. Maybe not altogether or in a big way. Maybe itll just develop a teeny, tiny tear that you cant even see unless youre right up close. And because you cant see it, you might not notice it until its too late and patching isnt enough. Youll need to replace your pool liner.

You May Like: Ways To Heat Above Ground Pool

Measure The Sidewall Slope And Hopper Width

This ones a little tricky.

Sidewall Slope:Extend one measuring tape across the back end of the pool. Run the telescoping pole down the sidewall of your pool until it hits the bottom. Thats where the slope ends. Lay the pole down onto the coping on the side of the pool. Extend your second measuring tape from the spot where the pole hits the pool edge to the first measuring tape to find the sidewall slope.

Determine the Hopper Width: Subtract both sidewall slopes from the full pool width to determine the hoppers width.

Important:We cant stress this enough. Measuring instructions online, whether written or in a video, only go so far. If youve never measured for a pool liner before, and you have any doubts about doing it yourself, we highly recommend hiring a professional to measure for you. If you measure incorrectly, and get the wrong size liner, youll be out a lot of money for something you cant use, and that cant be altered.

Measure The Hopper Width And Slope

Pools have various slopes that make the floor of the pool challenging to measure. At this stage, you will want two poles that you can measure. First, vertically drop one pole to the point where the side slope meets the hopper. Then, from the side of the pool, extend a horizontal pole to meet the vertical pole.

Where the poles meet is the slope measurement. You will get a measurement on the vertical pole and the horizontal pole. You will need both to get the slope measurement. Then, subtract the sidewall slopes from the full pool width to get the width of the hopper.

You May Like: Unclog Skimmer Line

What Can I Do To Make Sure My Liner Lasts As Long As Possible

Whether you decide to use thinner or thicker vinyl, you want the liner to stay in good condition. Youll have the best luck if you keep up with the maintenance in these three areas.

First, maintain your water chemistry. Specifically, its important to keep chlorine and pH within the ideal range.

Second, ensure the liner is installed properly. If youre not installing it yourself, ask the professional installer questions to be sure the company knows what theyre doing.

Third, try to keep dogs out of the pool as much as possible. If they do get in, keep them away from the liner. Basically, try to reduce the chance of puncture.

Inground Pool Liner Measuring Tips

Tools You Will Need: Some of the areasthat need to be measured are not easily accessed. To measure these, youwill need to use the plumb bob, string, skimmer pole and tape measure.

Step 1.Let’s say you want to measure the distance from the edge of the hopper to one of the side walls of the pool. At the end of your skimmer pole is a hole that “locks” the skimming net in place. Remove the net and feed the string of the plum bob through the hole. Lay the pool pole on the pool deck at the deep end and keep extending it out, perpendicular to the end of the pool as shown in the diagram below. When the plumb bob is at the intersecting point where the floor and the wall meet, place a pencil mark on the skimmer pole right at the edge of the coping. Place the pole on the deck and measure from the pencil mark to the string hole at the end of the pole. This is the distance you were looking for!

Step 2.To measure the depth in an inaccessible area of the pool, you will need your poleset-up again. Lay the pool pole on the pool deck. Extend it out, until the plum bob is just touching the bottom. Makea mental note as to where the string is entering the water and remove thepole to the deck. Measure the string to the end of the plum bob as shown in “A” in the diagram below. Now measurefrom the water surface up to the liner track. Add the 2 numbers togetherand this gives you the actual depth of the pool in that location.

Read Also: How To Unclog Swimming Pool Pipes

Next Day Delivery Details

Dohenys is pleased to offer free next day delivery at no additional charge for orders over $100 to most of the US for all Doheny’s brand chemicals and many of our most popular swimming pool supplies. Next Day Delivery Service does not mean Next Day Air, but simply that your qualifying products will be shipped from the warehouse closest to you resulting in delivery the next day. We do have a shipping charge of only $9.99 for orders under $100.00.

Some details regarding this service:Other than for Pleasant Prairie, Wisconsin, not all products are stocked at all locations and therefore not available for next day delivery. Only those items with a Next Day Delivery designation on the product page can be expected to arrive the next day and orders must be placed by 3 PM local time .

If you reside in the next day delivery area served by our Pleasant Prairie facility, order in-stock products and place your order by 3 PM Local Time you should receive your order the next day . This applies to products even if they do not have a Next Day Delivery designation.

Because next day delivery is not guaranteed for standard service and residential deliveries are made only Monday through Saturday though Saturday delivery is not guaranteed, there is a chance that our product will not arrive the next day. While we try our best, unexpected demand can cause products to occasionally be out of stock or create a warehouse backlog that also can prevent shipment the day of the order.