Saturday, November 26, 2022
HomeExclusiveHow To Hook Up Hayward Pool Pump

How To Hook Up Hayward Pool Pump

- Advertisment -

Hide Gaps In Drywall With Oversized Plates

Hayward 6060 booster pump install

Any time youre installing power switches, its fairly easy to reduce a hole in the drywall that is actually big. Fortunately, there are extra-large plates available at hardware stores that you can use to cover your switches.

They are typically in measurements up to 3/4 inch wider and longer than regular switch plates. The majority of people wont be able to tell the distinction, unless theyre professional electricians or fellow DIYers.

What Is A Hayward Pool Vacuum Pump

A Hayward pump is a vacuum breaker that pumps various liquids into your pool. The liquid is then filtered, and the water you used to clean your pool remains in place.

There are several filters on these vacuums so that you can choose one suited for different applications or cleaning situations such as heavy debris and sand or light dirt.

The pump allows you to vacuum your pool and return the water to your skimmer. It is made up of material that is resistant to low-water pressure limits.

This prevents it from breaking down after heavy use and strain on the unit and handling several dropouts or failures. It can also be upgraded with filters that adjust water pH levels.

Determine The Placement Of The Pool Pump

If youre replacing a busted pool pump with the same model then youll have nothing to worry about and installing the new pump is as simple as swapping out the old pump with the new one. If youre upgrading to a newer model, youre probably going to have a smaller, sleeker model which means that its probably going to sit lower than your existing pump.

This is not a problem, many pumps have adjustable bases that you can raise so that you can easily align it with your current fittings. If it still sits too low then use something stable like paving blocks or bricks to prop up your new pump.

Recommended Reading: Vdara Hotel Pool

Vacuum The Bottom Of Your Pool

After you’ve balanced and shocked your pool, you should leave it overnight. The final step is to vacuum your pool in order to remove any debris that has built up on the bottom.

If you covered your pool up properly in the fall you won’t have much to vacuum. However, there will no doubt be some debris that will need to be addressed, and its always better to ensure that your pool is as clean as possible.

Hayward offers some of the most powerful, yet efficient robotic pool cleaners on the market.

How To Hook Up Pool Vacuum To Hayward Pump

Hayward pool pump hose hookup diagram

Pump pool vacuums are a popular choice for cleaning pools, but it can be tricky to get the hang of it. They are not as simple as they look, and using them can require patience and attention to detail.

A powerful, efficient pool cleaner needs to be used with the proper pump and vacuums.

It is one of the best machines to have around your pool. It provides your pool with the filtration it needs to stay clean and healthy.

Hayward manufactures a wide range of pool pumps and accessories. Many pool owners have questions about connecting a Hayward pump to their existing vacuum system.

Recommended Reading: Swimex Pool Price

Pool Chlorinator Safety Tips

  • Turn off pool pump before opening your chlorine feeder.
  • When removing the lid, stand aside, hold breath to not inhale chlorine gas.
  • When winterizing, be sure to remove all chlorine from the chamber.
  • Only use Slow-Dissolve Tri-Chlor tablets in your chlorine feeder.

Swimming pool chlorinators have made it easier and safer to chlorinate your pool water. They are also affordable and manufactured in different sizes for all types of pools and spas. Aboveground pool chlorinators and inground pool chlorinators are available, and installation is quick and easy. If you are feeding chlorine tablets through the skimmer or through a floating chlorine dispenser, theres a better way!

With regular maintenance and a few replacement parts every few years, your Hayward Chlorinator can give a lifetime of service!

Pump Is Shutting Off By Itself

Not a good sign usually. If it turns back on after 15 minutes, it likely has been overheating. Provide shade if necessary, and make sure that air is circulating freely under all parts of the motor, and that the motor vents are open. Rake around the area to remove any leaves or mulch, and trim back overgrown bushes and overgrown trees that may block cooling breezes.

Other causes of a pump shutting itself off include loose or broken wires or incorrect voltage, more than 10% more or less of the rated input voltage. In most cases however, a motor that is over-heating tends to be defective beyond repair, when caused by an internal short across the motor windings.

Also Check: Algaecide Ace Hardware

What To Do If Your Pool Pump Is Too Low

If your new pump is too low, then theres a quick fix for that. Simply cut the incoming vertical pipes for the skimmers and the drains and attach some couplings to raise the manifold about an inch or two and you should be good to go. Another way to go about this is to use two 45-degree elbows on the horizontal pipe to raise it up by two to three inches. Whichever way you go about it, just make sure that its sealed properly with some silicone sealant and PVC glue.

The Cleaning Power Of Hayward Pool Vacuum Pump

Pool Opening 2020, Part 3 – Hooking Up The Pumps

Hayward pump can process hundreds of gallons per hour. This means that you can clean your pool quite quickly, catching all kinds of substances in its filter.

The cleaning performance is impressive and hard to beat, especially because Hayward Vacuum Pumps are relatively inexpensive compared to other vacuums.

This versatility allows you to use it for various swimming pool cleaning jobs or aquarium filtration duties.

For example, if your spa is clogged with dirt and debris from a hard winters snowfall isnt coming out quickly the pump can come in handy by sucking up any waterproofing compounds left on the walls of your spa or swimming pool.

Recommended Reading: Cya Reducer For Pool

Pump Is Not Pumping Water

If the pump is not pumping water at all, check that all suction and return valves are open, and the pump lid is on tight, with the lid o-ring in place. Lubricating the lid o-ring regularly will help improve the seal. Check that the drain plugs are tightly inserted with Teflon tape, and that the pump basket is inserted in the proper way, and is sitting all the way down.

If the pump has lost prime completely, fill a bucket with water or bring over a garden hose and re-prime the pump manually by filling up the pump. If the pump wont catch after a several attempts to fill with water, check for an air leak on the suction side of the pump, an obstruction in the line, or low water level.

If you just pulled the pump to check the impeller or replaced a shaft seal, make sure the seal is installed correctly and that the diffuser and diffuser gaskets are seated firmly.

If the pump wont pump water fully, check that:

  • Suction side valves are open.
  • Older suction side valves can leak air through stem or lid.
  • Pump lid o-ring is a good fit, in good condition, and lubricated.
  • Pump lid cover is Tight .
  • Impeller is not clogged with small debris.
  • Check that pump basket is not broken or misaligned.
  • Pool Filter is clean, and filter valve is on Filter or Recirculate.
  • Return side valves are open.
  • Pump does not drip water from plugs or seal when pump is off.
  • Test entrance pipe fitting for Air leakage.
  • Use shaving cream or soapy water to see if it sucks into pump.
  • Assembling Your Vacuum And Hose

  • 1Assemble the vacuum hose by twisting the hose pieces together. The size of your vacuum hose is dependent upon the length of the pool. The hose must be long enough to reach every section of your pools floor from the location where youre installing it. On most vacuum systems, all you need to do is screw the threading together for each section of hose until youve assembled the whole hose.XResearch source
  • Read your specific vacuums manual to find out where you need to install the end of your. Each brand and variety of vacuum is different, but most of them hook up to the filter, open skimmer, or suction port.
  • Some hoses will need to be assembled in a specific order. Consult your specific vacuums instruction manual to see if there is a unique order that you need to attach the hose sections in.
  • 2Submerge your hose in the pool to fill it up with water. You dont want any air in your pump system, so you need to remove all of the air from the hose before using it. Place it in a deep section of the pool and push each section down until you see all of the air bubbles escape.XResearch source
  • To do this quickly, hold the opening of your hose near a jet on the side of the pool. The jet will force water through the hose.
  • To hook up your hose to the open skimmer, take the end of your hose and attach it to the adapter with the unthreaded side on the end. Stick the adapter inside the skimmer by fitting it into the opening under the lid.XResearch source
  • Don’t Miss: Ymca Fishers Pool Schedule

    Removing The Old Pool Pump

    Important Note: Were going to start tinkering with the pump now so turn of the mains that lead to your pool system to eliminate the risk of shock.

    If your pump is hard-plumbed into the system cut the pipes coming in and out of the pump. Be sure to leave a couple of inches to attach unions for future use.

    Once the plumbing has been removed, its now time to remove the wiring. Double check if the mains are off, we cant stress that enough.

    Remove the rear cover plate. Once this has been removed, you should see three wires connected to the pump motor. Gently loosen the wires from their fittings with a flathead screwdriver to disconnect them from the pump. Once this has been done, look for the conduit fitting, this looks like a steel elbow fitting that brings the wires into the motor, locate the nut that holds the conduit in place and loosen/remove it. Once this has been fully loosened or removed, gently pull out the conduit and the wires should be free of the pump.

    Remote Pool Management System

    34 Hayward Pool Pump Hose Hookup Diagram

    Hayward AquaConnect gives you four ways to manage every essential pool, spa, and backyard function. AquaConnect Web allows you to manage your pool via the Internet from anywhere. The NEW AquaConnect App for iPhone® and iPad® makes it easier to access your pool from your smart device, and streamlines platform use to make settings easier to change and diagnostics easier to read. AquaConnect Home Network communicates with web-enabled computers or handheld, WiFi devices in your home to control all pool functions. And AquaConnect Home Automation provides a serial option for seamless integration with your existing home automation system so that one keypad or display panel can handle home theater equipment, security, lighting, landscape sprinklers and other backyard functions.

    AquaConnect App

    The AquaConnect App can be downloaded to the iPhone or iPad. The FREE App streamlines the pool and spa management process, providing faster access to AquaConnect, as well as adapting what you see when using your smart device. This creates simpler platform navigation, and makes controlling settings and adjustments easier.

    Android App available early 2014. Available on ProLogic, AquaPlus, and AquaRite Pro.

    AquaConnect Web

    Also Check: Hydroflush Pool

    Installing The New Pool Pump

    After youve removed the old pump, position the new pump in place but dont attach anything yet. Align all of the pipes and the couplings first, adjust the height and everything but dont do the plumbing first. The first thing you should do is to reattach the wiring. The reason for this is you may need to move the pump around to get easier access to the electrical parts and you cant do this if your pump is already attached to the pipes!

    Attach the conduit from the old pump into the threaded port of the new pump and refer to the wiring diagram on how to attach the wires properly. If its not on the pumps body, then refer to your owners manual. Once the wires have been attached and the pump closed up, its now to proceed with the plumbing.

    How Do You Hook Up Hoses To A Pool Pump And Filter

    To hook up hoses to a pool pump and filter, attach the other end of the hose from the skimmer pipe to the pump, connect the opposite end of the return hose to the pool filter valve, and attach another hose to connect the pool pump and filter together. Hose clamps and water pump pliers are necessary to complete this project.

  • Attach the pump hoses to the pool

    Connect a single pump hose to the skimmer pipe located below the skimmer basket. Lock down the hose that is over the pipe with a hose clamp. Attach the opposite end of the hose to the pump. Connect the return hose to the pools fitting pipe, and clamp it down. Connect the other end of the return hose to the return valve of the pool filter. Make a tight seal with the hose clamp.

  • Connect the pump and filter

    Use another hose to make the connection between the pump and pool filter, and use water pump pliers to secure the connection. Use hose clamps to seal the pipes and hoses.

  • Activate the pump

    Prime the pump, and prepare the filter by using a filtering conduit, such as sand. Plug in the pool pump and filter. The pump and filter should be working.

  • Check the connections

    Inspect all of the hoses and connections, and tighten the clamps if necessary. Listen for smooth sounds coming from the pool pump and filter.

  • Read Also: Chlorine Pool Calculator

    Reinstall Skimmer Baskets And Return Jets

    Its almost time to start up your pool. Before you flip the switch, you’ll want to remove the ice compensators from the skimmer put your skimmer baskets back and screw in the return jet eyeball fittings that direct water into your pool.

    At this point, you should also check your water level. If its not at its normal level, add water to your pool.

    Reattach And Reinstall All Pool Equipment And Accessories

    How To | Hayward ProLogic Automation | Setting Up a “One Touch” Button For the Spa | Chlorine King

    Depending on the type of equipment you use for your pool, you may have to take it out of storage and reattach it. While some people leave pool items in the same place all year round, others prefer to put them away during the wintertime to avoid exposing it to the elements.

    Regardless of your approach, always make sure your pool pump and pool filter are secured in place. You’ll also want to remove any winterizing plugs that were installed during your pool closing. Make sure all of your equipment is ready to get back to work.

    After reattaching your pool equipment, you should reinstall your deck equipment. Everything from the ladder to the diving board.

    TIP: You should also lubricate any nuts and bolts that exist on these pieces of equipment so that they don’t rust on you throughout use.

    Don’t Miss: Aria Cabana

    Pump Trips The Breaker

    When the breaker trips when trying to turn on the pump, most likely the motor shaft is frozen, the impeller is stuck, or the capacitor has blown. In some cases, it can be a bad breaker, especially one that is used often to turn the pump on and off.

    If the breaker trips while the pump is running, the pump is likely drawing more amperage or voltage than the breaker rating. This could be caused by incorrect voltage or from clogged or restricted pipes, valves or impeller. It could also be just a bad breaker.

    If the breaker trips when turning on pump, check:

    • Look for wire problems in back of motor crimped, split, touching.
    • Check the motor shaft, the impeller should turn freely by hand.
    • Shut off power at breaker and tighten all wire connections.
    • Check timer clock or switch for burnt terminals or wires.
    • Check capacitor for capacitance or resistance with an Ohm meter.
    • If breaker still trips, replace the breaker they go bad eventually.

    Pump Flow Rate Is Low

    When the filter pressure is high, the filter is dirty ~ and when the filter pressure is low, the basket are dirty. Lower than normal pressure on the filter corresponds with lower than normal flow rates.

    Check the pump impeller by removing the pump basket and reaching through the hole to feel for any debris or rocks stuck inside the impeller. If you feel anything unusual, remove the bolts to pull the motor out for a good cleaning of the impeller.

    An air leak will also reduce water flow rates, as air is drawn in to the pump, and a dirty pool filter or baskets can clog up the works, and reduce the flow rate. In some cases, it can be a clog in the skimmer line, or even a partially collapsed suction line that is to blame.

    Don’t Miss: Cleaning Concrete Around Pool

    Treat The Water Properly

    Start by checking your pH, alkalinity and calcium levels so that you know how to move forward with balancing your pool water.

    Once properly balanced, you’ll want to shock your pool with a quality shock treatment to get rid of all that winter algae buildup. We recommend you wait to shock your pool until the sun starts to go down for it to be most effective

    Check out this chart to help balance your pool:

    Test

    RELATED ARTICLES
    - Advertisment -

    Most Popular

    - Advertisment -