Monday, May 16, 2022
HomeMust ReadHow To Get Water Off Pool Cover

How To Get Water Off Pool Cover

- Advertisment -

How Does It Work

How To Remove Excess Water on A Pool Cover With A Cheap Manual Siphon Pump

Operation of this tool is pretty simple. A sort of pump action causes it to work, and it will act as a regular pump to suck up water with each hand motion, or as a siphon to continue water flow after a single motion.

  • To use this device, you will connect a hose to each side.
  • One will go into the water on the cover, and the other will go out into your yard to direct the water where you want it.
  • A simple pump action will start the water flow, and it will continue just like a regular siphon would.
  • The difference is that you never had to touch the water, suck on the hose, or use any special movements or techniques in order to begin the flow. The fool-proof action requires no trial and error, and ensures that you will get the siphon started no matter what your expertise level is. What is similar is that as long as plant matter and other gunk is small enough to go through the hose, it will not clog things up, or cause problems as you work. As an up side, if you have small amounts of water left over, this is the only method that can effectively deal with it. At a certain point, the siphon will stop, and the water will no longer flow. When this takes place, just switch to a regular pumping action to pull the remaining moisture up and off the cover. When using this tool, youll remove more water with less effort, and youll finish the job with ease.

    Solid Swimming Pool Covers

    • Check waterline periodically. Heavy debris, water, and snow loads, combined with a low waterline, can add excess strain on your cover, reducing the lifespan.
    • Clean every 3-6 months using a garden hose, pool brush, cover pump and mild detergent such as dish soap. Put the cover pump on the pool liner. Apply detergent and wet with a hose. Then use a pool brush to scrub the liner. Once clean, rinse with a garden hose and remove accumulated water using a cover pump.
    • If you have mold developing on your pool cover, clean your cover with bleach, then spray off with a garden hose. To avoid mold growth, make sure your cover is completely dry before storing when not in use.
    • Check periodically for rips or tears in your cover. Patch kits are available and should be used immediately as holes in the cover can compromise the cover.
    • Make sure to avoid covering your pool within the first two hours after applying chemicals to your pool. This prevents damage that can be caused by pool chemicals.

    How To Drain A Pool Cover

    Drain it during a heat wave and youre and you can see damage anywhere from pool liner damage to cracked pool walls and floors.Draining and refilling, then adding new chemicals will refresh the water in an otherwise undamaged pool.During installation, all drains should stick up from the floor.Ez drain covers come complete with.

    First, remove any debris that is still on the cover while the cover is still in the pool.Free shipping on orders over $25 shipped by amazon.Free shipping on orders over $25 shipped by amazon.From there, you need to close the skimmer valve and open up the main drain.

    Get it as soon as fri, apr 30.Get it as soon as fri, feb 12.Ground water under the pool can flow through the valve into the pool to equalize the pressure.How much a swimming pool drain should cost.

    How to cover the main drain on a pool.If possible, drain the pool when the outside air temperature is less than 85°f.If the cover is missing or broken, children and bathers can get body parts, hair, and jewelry trapped in the drain, or become suctioned to it.If the same water has been in a pool for several years, the levels of total dissolved solids can be high.

    In this example it only took to full pumps to start the siphon.In turn, this damages the drain cover.Install drain cover by placing ring over main drain.It looks like a drain fitting with a cover at the bottom of the pool.

    Your new drain should be sized sufficiently to fit into the drain hole.

    Recommended Reading: Build An Inground Pool

    How To Choose The Best Pumps To Remove Water From Pool Covers

    Investing in the best pumps to remove water from pool covers will be an uphill battle due to the plethora of them available on the market today. So, to avoid buying a pool pump below the belt, you need to understand how it works. Nevertheless, to make it easy and simple to do, weve mappedcertain factors you should consider when selecting a pool pump. Below are the factors!

  • Price
  • Durability
  • Cord length
  • Its vital to cut your coat according to your size when choosing a pump to remove standing water on the pool cover. Meanwhile, most pumps are quite affordable. Moreover, the higher the price, the higher the quality. Since you want a reliable pool pump, you should be ready to pay more for them.

    Also, you can either choose from an automatic pump or manual. You can as well check for their distinctive features before purchasing them. Do not forget to check for the pumps cord length and filter efficiency. Its longevity also saves you more money. What else? Ensure you consider how many gallons of water the pool pumps can remove per hour.

    Blue Wave Dredger Jr 350 Gph Above Ground Pool Winter Cover Pump

    How to remove a pool cover

    Blue Wave Dredger Jr., 350 GPH Above Ground Pool Winter Cover Pump is a nice water pump. It clears most of the dirt, debris, and water accumulated on your pool cover. It is a submersible pump. In order to prevent clogging, it includes a reusable foam filter.

    The base of the pump is wide, thus keeping the pump stable while it pumps out water. It has a 25 ft. long power cord, thus eliminating the need for an extension. Meanwhile, the flow rate is 350 gallons/hour.

    You need to turn it on and off manually. It can remove water up to a depth of 1/8 inches. The pump includes a garden hose adapter as well.

    Our rating:

    • Doesnt shut off automatically
    • Plastic is not very durable so it might not last long
    • Takes a bit longer to clean up the water

    Also Check: How Long Should A Pool Pump Run Per Day

    Always Remove Excess Water From Your Tarp Style Winter Cover

    It is vital to remove excess water from solid tarp style winter covers, commonly used on above-ground and some in-ground pools, to avoid damage to the cover and the pool. This can easily be done with a submersible pump on your pool cover whenever temperatures are above freezing, and liquid water is present. This frequently occurs in fall before freezing temperatures arise, during winter when unseasonably warm temperatures exist for several days in a row, and in spring as temperatures begin to rise.

    Above-ground Pool Tarp Cover: The typical tarp style cover is secured to your above-ground pool wall and top ledge with a steel cable that is tightened around the pool. As water accumulates on the pool cover, unless the water in your pool is frozen, the water weight on the cover displaces water from inside your pool, out through the return hole and/or skimmer. As this occurs, stress increases as your pool cover strains against your pool wall and top ledge.

    Consider that water on a 24 round pool weighs about one ton per inch deep. So, six inches of water on your pool cover, weighing over 6 tons, can put a fair amount of strain on the cover and pool.

    As stress from water weight on your cover increases, first, your cover starts to stretch. This can lead to thin spots, pin holes and tears in your pool cover. As the cover pulls the steel cable up against your pools top ledge, the top ledge can be broken and even pulled off the pool wall.

    Posted onbya1pool_fun|Posted in Service

      Siphoning The Water From The Pool Cover

      The first method to remove water from the pool cover is to siphon the water from a pool cover is to use an ordinary hose. This method will require that you access the edge of the pool cover and have a pipe thats long enough to reach the top of the cover and have the other end in an emptying location.

      To siphon the water from the pool cover, follow these steps:

    • Manually remove any huge debris including branches, leaves or any other object.
    • Attach a high-density object such as a stone or metal on one end. The attached object helps to force the hose pipe to get to the bottom of the water. Ensure the attached object does not block the hose pipe.
    • Place it on a faucet then turn it on. The aim is to fill the pipe with water to get rid of any air which may hinder the continuous flow of water.
    • With the water from the faucet still in the hose, and drop the end with the attached object into the water on the pool cover.
    • Place the other end in an area that is free from any standing water. Ensure the hoses end on the pool is higher than the other end for the water to flow.
    • Once the water starts flowing out, place it at a low point until it has flowed out from the pool cover.
    • At all times, make sure the end on the pool cover is submerged to avoid sucking in any air which could stop the siphoning process.

      Advantages

      This method has following the advantages:

      Disadvantages

      This method has following disadvantages:

      If you dont have any tools to work with, this is the best method to go for.

      You May Like: Pool Pump Impeller Clogged Symptoms

      Remove Water From Your Swimming Pool Cover

      Maybe youve just survived a large rain or snow storm and want to perform some preventative maintenance in order to ensure that your pool cover lasts for the remainder of the winter, or maybe youre just opening your pool for the season. It doesnt matter what has prompted you to do so, but sooner or later, all pool owners will be faced with the task of removing the yucky water that has accumulated on top of the cover. Whether you have an above ground, or in ground variety, if you cover your pool to prepare it for winter, it will inevitably collect water prior to you taking it off to use the pool again in the summer. If left on there under heavy rains or snows, the weight could be so burdensome that it pulls the whole cover into the pool to create a disastrous situation for you to clean up. If youre lucky enough to not have to remove some mid-winter water accumulation, then you will still be faced with proper removal to be able to open your pool when the weather changes.

      The Best Pool Cover Water Pumps

      How To Remove Rain Water From Your Pool Cover (With Only Water Hose!)

      Without any doubt, over a hundred thousands of pool cover water pumps are on the shelves. So, selecting the best of all might be a daunting project. But you know what? All you need is this guide. Well help you choose the best pumps to remove water from the pool. All pumps selected are of high and excellent quality. How about we check them out?

      You May Like: Venetian 10th Floor Pool

      Remember Snow Will Melt And Refreeze

      If you position your cover pump correctly on your pool cover, the pump will do most of the work for you to help manage the snow melt or existing ice as it melts. With automatic cover pumps, they will begin pumping once they are submerged to a certain point and can run throughout the entire winter season. Manual pumps, on the other hand, are turned on and off as needed. At Swimming Pool Discounters, we have a wide selection of high quality, competitively priced pool covered pumps to save money and your cover.

      Another effective way to manage snow and ice on your pool cover for above ground pools is to use an air pillow. An air pillow floats in the center of the pool underneath your pool cover to prevent the pool surface from freezing solid all the way across and will also help to channel the water to the cover pump. This protects the pool walls from severe and costly damage. An air pillow should always be used for aboveground pools.

      What To Do When Your Pool Cover Falls In

      In Maintenance and Repair by John & Sabrina FoleyOctober 26, 2015

      When you own a swimming pool you do everything you can to keep it clean and in good condition, including using a pool cover. Pool covers are beneficial many ways. They can reduce dirt and make cleaning easier, and they can keep the water a little warmer which means you have more time to enjoy it. However as with any other swimming pool device or accessory, pool covers can also have their problems.

      Also Check: Pool Pump Capacitor Test

      Removing Water From A Pool Cover With A Garden Hose

      If you have an above ground pool, it is possible to remove the water with just a garden hose. Heres the trick:

    • Connect your hose to the faucet.
    • Place the other end of the hose on top of the pool cover. Make sure it is underwater, and placed in such a way that it will stay under water.
    • Turn on the water and let it run for a minute.
    • Turn off the water and quickly disconnect the hose from the faucet. The water from your pool cover will now start to drain.
    • We prefer to use non-kink hoses like this one:

      Advantages:

      • You dont need to invest in a pool pump, which can range in price from $50-150.
      • Its simple and quick.

      Disadvantages

      • The hose in the pool can move around, causing the draining process to stop.
      • You are limited to where you can drain your pool water. Once you detach the hose from the faucet, its tricky to move the hose. Just plan ahead and know where you want the water to drain.

      Top 8 Best Pool Cover Pumps Of 2021 Reviews

      Products to Remove Water off your Pool Cover

      Having difficulty removing accumulated water from the top of your pool cover? You are not alone. All pool owners face the same problem when opening their pools for the seasons.

      Before buying the best pool cover pump, you should know what kind of best pool cover pump you are buying. Their specifications and usage instructions differ from each other.

      The number of pool cover pumps available in the market is very large. Thus, it can be a little difficult to buy the best pool cover pumps which suit your needs perfectly.

      Below, youll find the features and the pros and cons of some of the best cover pumps. So, depending on your requirements, you can pick one which you think is perfect for your pool!

      This article will definitely save you a large amount of time and effort. It will help you in choosing the best pool cover pump suited for your needs! So, have a look at the eight best pool cover pumps!

      Contents

    • 500 GPH Universal Pool Cover Pump
    • Also Check: Can You Heat An Above Ground Pool

      Gph Universal Pool Cover Pump

      500 GPH Universal Pool Cover Pump is a submersible pump. The flow rate of this pump is 500 gallons an hour. Thus, it is suitable to use in pools, basements, and other places such as ponds, etc. In fact, it works well for medium-sized pools.

      It is lightweight and compact. It weighs a little over 3 lbs. Since it uses the standard electrical output, you can use it almost anywhere. It is easy to set up is quite fast and works for both in-ground and above ground pools.

      Our rating:

      • The pump is not automatic.
      • It tends to clog easily

      Wayne Wwb Waterbug Submersible Pump With Multi

      WAYNE WWB WaterBUG is a pool cover submersible pump. It removes the water as well as dust and debris from the pool cover. You can use it to remove water from roofs, grounds, and other flat surfaces. It has a compact size thus it can be used in small and tight spaces as well.

      There is discharge on the side of the pump which helps the water to flow out of the pump pretty easily. It has a flow rate of 1257 gallons in an hour. For optimal discharging of water, this pump uses Multi-Flo technology.

      Our rating:

      • Takes a little bit more time as compared to other pumps
      • Needs to be monitored

      Recommended Reading: Is The Venetian Pool Open

      Little Giant Automatic Swimming Pool Cover Submersible Pump

      Little Giant APCP-1700 is an automatic swimming pool cover pump. Despite its compact size, it has a flow rate per hour of 1,700 gallons. Upon reaching the level of 3 ¼ inches, it automatically stops. The power cord is 25 ft, 110 V.

      It works well with large pools. Since it is made up of stainless steel, it is pretty durable. It has a 3-year warranty. Moreover, since it has an integrated float switch, you do not need to monitor it constantly. You only need to plug it in, and it will do the rest.

      If you want to clean it, you can easily take it apart. The intake screen is also easy to remove and clean. Thus, it is pretty easy to maintain and clean it. Moreover, the built-in handle makes it easy to move the pump around.

      The motor of this pool cover is pretty energy efficient. The wide base makes sure that the pump remains stable. It is very lightweight, weighing just a little over 11 pounds.

      Our rating:

      • There might be some air locking issues
      • Needs to be unplugged under freezing temperatures
      • If it breaks, it is pretty hard to find replacement parts.

      RELATED ARTICLES
      - Advertisment -

      Most Popular

      - Advertisment -