How To Hook Up A Pool Vacuum
How does a pool vacuum work, and how do you attach all the parts? Unlike your carpet vacuum cleaner thats ready to go, there are several steps to take when preparing to vacuum your pool. Here is how to hook up pool vacuum and prepare it for cleaning.
- Vacuum hose
To hook up a pool vacuum, screw the telescoping pole on the vacuum head and attach the vacuum hose.
Extend the pole so its long enough to reach the bottom of the pool, and submerge the vacuum head to the pool floor. Position the other end of the hose at the return jet hole to fill the hose with water.
Remove the skimmer basket from the intake hole and set it to the side. Without taking the hose out of the water, move it from the return hole to the intake hole or vacuum plate and place it into the opening.
D What Is The Pool’s Existing Filtration System
It is crucial to know the filtration rate of the pool cleaner to ensure you will get better quality water. It is also necessary to ensure the water has gotten an excellent cleaning as you would have intended. Ideally, the pool cleaners should be able to filter at least 70 gallons of water every minute.
Installation Steps For A Hydraulic Swimming Pool Robot
The installation of a hydraulic swimming pool robot such as automatic suction pool cleaners requires a few additional actions to that of an electric cleaner, but it remains relatively simple to perform.
Unlike the electric model, the hydraulic robot is not equipped with its filtration system. It uses the swimming pool pump, to which it must therefore be connected. To do this, here is what to do.
The first step is to assemble the hose. To do this, assemble the hose sections to reach the part furthest from your pool, then add 2 more sections. So your robot vacuum cleaner will have a sufficient length of hose.
To properly connect your hose to your broom plug or your skimmer, immerse it to expel the air present in it. Do not hesitate to place it in front of a delivery nozzle to facilitate its filling. Once the hose is full of water, connect it to your system. In the case of a connection to a skimmer, remember to install a conical adapter, as well as a 45° elbow.
To connect your robot vacuum to your filtration system, submerge it to expel the air, then connect the vacuum cleaner to your hose. Once the connection is correctly made, let it sink to the bottom of your pool.
Finally, turn on your filtration system to start cleaning. If necessary, adjust the suction rate of your system.
If you encounter any difficulties in correctly installing your hydraulic swimming pool robot, do not hesitate to contact your manufacturer.
Also Check: Aria Cabana Cost
Vacuum Bottom Of Pool
1. Slip skimmer disc into skimmer. You might be required to plug thehose end into suction port.
If thats the case be certain to pull out hose end out of the pools water to fix skimmer disc as quickly as possible. In the process make sure not to let any air into hose.
2. Slowly move head back and forth over the bottom of pool. Do this from a position where you can clearly see the bottom of your pool. Be certain to overlap the previous path each time you pass the vacuum head over the bottom surface of the pool.
3. Vacuum until the whole floor is totally clean.
4. Use a 3-brush vacuum head for more thorough cleaning. This is an efficient way to loosen tough debris on the sides and bottom of the swimming pool.
These units are designed to reach nooks and crannies more easily. You can also use this type of unit for cleaning your pools steps.
How To Vacuum Pool To Waste Cleaning A Dirty Pool
If you have a very dirty pool, particularly when you open it in the spring, it is likely that the only way to clean it properly will be to vacuum pool to waste. This means using the waste setting on a sand filter multiport valve in conjunction with your pool vac.
Vacuuming pool to waste will remove all dirt or algae from the bottom of the pool by sending it via the waste line either to your sewage system or into your yard, instead of going through the pool filter system. This prevents the filter becoming clogged and fine particles going back into the pool.
If you try to vacuum a very dirty pool using the more usual Filter setting then it is likely that the pool filter will become clogged and may even start to allow dust particles and other debris through which will then end up back in the pool.
The other reason you may need to vacuum to waste might be if you have a heavy infestation of algae. Algae particles can be too small to be caught by the sand or other filter medium so if vacuumed on the filter setting they will probably just end up being redeposited back into the pool. So in this situation vacuuming to waste is the best solution to remove the algae from the pool after it has been killed using shock treatment..
Read Also: Salt Calculator For Pool
Make All Necessary Connection To The Adapter Ports Provided
Here is where you need more of the manufacturers manual to get all necessary fitting plugged to the adapter. Make all connections as specified by the manufacturer into the suction port of the skimmer. The position of suction ports could vary depending on the model and manufacturer of your pool.
Some suction ports are found a little bit underneath the pool, positioned near the middle of the pool. Others are located inside the skimmer canister at the pool deck. Check the configuration manual on how to attach the elbow fitting to the suction port in the skimmer. In any way your configuration comes, it is always designed to allow the vacuum hose to be supplied from the flapper door.
Ways To Maintain Your Pool
The best thing you can do to keep your pool clean is to set up a regular cleaning and maintenance schedule. Monitoring and daily cleaning go a long way to keeping your swimming pool ready for use at all times.
- Pool vacuum
Setting up a pool maintenance routine is a great way to ensure that youre swimming in clean and fresh water each day. Use a leaf skimmer daily to clean the water surface and remove bits of debris and floating leaves, and vacuum the pool once a week.
Test the water for the proper pH, alkalinity, chlorine, calcium hardness, and cyanuric acid and keep them in the recommended level ranges. Clean the pump DE, cartridge, or sand filter when the pressure gauge increases above normal or every six months.
There are so many parts to a swimming pool that it is often confusing, from the pool filter and pump to the skimmer and vacuum. Once you understand each component and how they operate, keeping your pool clean is easier than you think.
Don’t Miss: How To Build Inground Pool
Vacuuming The Above Ground Pool
Move the vacuum on the waters surface the same as you do it to clean the rug or carpet in the room. Make sure to clean the pump strainer after short intervals if your pool has too much debris. Slowly move the head back and forth to make sure every corner of the bottom of the pool is clean, and do this work with patience.
The foremost important thing is to maintain the head underwaters position all the time, or it will lose its prime. Furthermore, repeat this procedure because you have to remove all the debris from the pool floor.
C What Is The Garden Hose Length
If you consider choosing the suction cleaners, you need to ensure that it comes with a proper hose length. This is one of the most critical features to achieve an effective above-ground pool cleaning process. If the vacuum doesn’t have enough length, it’s pretty much useless, no matter how powerful it is.
Don’t Miss: Tibbits Pool Yonkers
How To Set Up A Manual Pool Vacuum
First, ensure the pump and filter are running. Attach the vacuum head to the open end of the telescopic pole. Attach one end of the hose to the vac head. If the hose is slippery, use a hose clamp to keep it in place.
Place the vac head, telescopic pole, and hose in the pool, making sure the vac head rests on the pool floor.
Place the other end of the vacuum hose against a return jet in the pool. This will push water through the hose and drive all the air out.
Triple-check to make sure the vacuum inlet is the only line open to the pump. If not, particles and debris will also be sucked in by the pump and undo all your hard work.
NOTE: Youll see bubbles rising from the vacuum head on the floor of the pool. Once the bubbles stop, all the air is out of the hose.
Attach the vacuum plate to the end of the hose youd previously placed against the return jet, block the opening with your hand, and bring it over to the skimmer. Be sure to create a good seal or suction will be lost.
If youre not using a vacuum plate, remove the basket inside the skimmer, and, using your hand, block the end of the water-filled hose. Then place the hose into the skimmer, making sure its firmly inserted into the suction hole at the bottom of the skimmer.
NOTE: Whichever method you choose will create the suction that pulls material through the vac head, up through the hose into the skimmer, and then through the filter system. If your vacuum loses suction, just follow the prep steps again to restore it.
How To Set Up Your Vacuum Cleaner
Step 1-Attach the vacuum head to the T-Pole
Step 2-Connect the vacuum head to the swivel end of the vacuum hose.
Step 3-Fully extend the T-Pole.
Step 4-Lower the vacuum head carefully to the bottom of the pool try not to disturb any debris on the floor.
Step 5-Connect the skim-vacuum to the other end of the hose.
Step 6-Once attached, place over a return fitting to purge the air from the vacuum hose.
Step 7-Keeping the skim vacuum close to the surface of the water, make your way to the skimmer without letting air back into the vacuum hose. Put the skim-vacuum into the skimmer through the top or the throat of the skimmer on top of the skimmer basket.
Read Also: Vdara Club
Disconnect Change Filter Settings And Do A Final Cleanup
Once your pool is vacuumed to your satisfaction, you can disconnect your vacuum head and hoses. Make sure to clear out the bottom of the skimmer, too. If you changed your filter pump settings, make sure to change them back . For a finishing touch, attach a brush to your telescoping pole and give the pool floor and sides a good scrubbing.
Pro tip: To ensure that your pool water remains balanced, test your water after you vacuum your pool.
Tools You Need To Vacuum An Above Ground Pool
A manual vacuum cleaning system is required to vacuum your above-ground pool. You will need different tools for this work. They are:
- A skimmer
- An extension pole
- A skimmer disk
You can remove the leaves and other surface rubbishes that are in your pool with the pool leaf rake. On the other hand, the vacuum cleaning system is consists of the extension pole, vacuum head, and vacuum hose.
You May Like: Green Pool Water From Iron
Start The Vacuum Process
Once you fill the vacuum hosewith water, remove it from the water-return outlet with its end part plunged.Now attach the skimmer disk to the plunged end. You need to join the skimmerdisk with the skimmer on the suction port to initiate the vacuum. Make sure thehose end remains plunged to prevent air from entering the hose.
Vacuum The Swimming Pool
To initiate the vacuuming process, slip the skimmer disk to the skimmer atop the suction port. On the other hand, If your vacuum cleaner requires that you plug the hose head into the suction port, you will need to carry out the insertion as fast as possible to avoid allowing too much air back into the hose.
Once done with either of the options, take a strategic position from where you view the bottom of the pool clearly. Move the vacuum head back and forth the bottom of the pool slowly. To effectively vacuum the entire floor of the pool, always overlap your previous paths.
Read Also: How Much Do Swimex Pools Cost
Why Do I Need To Vacuum My Pool If I Have A Robotic Pool Cleaner
If youve ever seen your robotic pool cleaner push a pile of waterlogged leaves from one end of your swimming pool to the other, you know what were talking about: Robotic pool cleaners are great for light, day-to-day maintenance, but theyre not designed for heavy lifting. If debris isnt removed promptly, it can wreak havoc on your water quality and lead to maintenance issues like algae. A pool vacuum makes short work of heavy debris, helping you keep your pool clean and inviting and preventing maintenance headaches.
S For Vacuuming Above Ground Pool
The process of learning how to vacuum above ground pool involves two main methods. You should know them whether youve just installed a brand new above-ground pool or are required todo it for someone else.
The two main methods are the manual and automatic method of cleaning the pool. The automatic method is faster and less strenuous. So if you want to clean your pool without spendinglots of time and effort then a robotic vacuum is a good option.
This convenience doesnt come without a priceliterally. So while an automatic vacuum is more convenient it also boosts the price of the unit.
These robotic pool cleaners can clean the entire pool. That includes the walls, cove, and floor. The result is a hands-free cleaning of your above-ground pool.
Then theres the manual vacuuming system. This involves the vacuum head with rollers/brushes, big plastic hose, and long metal/fiberglass pole. Since the vacuum is manual it means youll have to roll up your sleeves to clean the interior of the swimming pool.
On the other hand, this can also provide some benefits. The costs are lower so you wont have to spend big bucks to vacuum the pool. You can also get in a good workout so if you want to lose some weight this is one of the best options when youre working on your pool.
An X-factor is when learning how to vacuum above ground pool a manual vacuum can help create pride of ownership.
Here are the various steps to manually vacuum your above-ground swimming pool:
You May Like: Will Chlorine Kill Head Lice
Lower The Vacuum Head Into The Pool
Lower the vacuum head with the pole and hose attached into the pool so that the head rests flat on the floor of the pool.
With the pool filter and pump running, place the loose end of the hose against a return jet in the pool to push water through the hose and remove all of the air. Bubbles will rise from the vacuum head. Wait until all of the bubbles have stopped to move the hose away from the return jet, but make sure the hose stays fully-submerged.
How Long Should Vacuums For Above
Although the pool filter might clean all the water in two hours, you might run it for a shorter period to save energy. However, the time depends on several factors, including the size of the pool, the amount of debris, and the season. For example, during summer, the chances of bacteria are higher, and it is recommended to run the vacuum for about 12 to 14 hours a day. However, bacteria and algae may not thrive in cold water.
Don’t Miss: How To Keep Spiders Out Of Pool
Remove Big Debris From Surface
1. Use a pool rake/skimmer to remove all the debris on the surface of the pool.
This includes leaves, twigs, bugs, and other big debris you can see floating on the top of the pool.
If you use a skimmer make sure to clean it out once the basket fills up with debris.
2. Use a lightweight/cordless pool vacuum for more convenience You can find many units at online retailers like Amazon.
This type of unit will make the process faster and easier. Such vacuums are bundled with rechargeable batteries and filters.
The main benefits are youll be able to clean the pools surface in less time.
However, its another tool that will add to the total cost of vacuuming/cleaning your pool.
So if youre on a tight budget for pool care/maintenance you might want to go with a standard pool rake/skimmer or even an old-school leaf rake.
This tool makes the process easier since you can quickly pick up debris like leaves, sand, and algae that are sitting at the bottom of the pool.
3. Turn on pump, take this step after youve removed debris on the surface of the above-ground pool. Make sure water is flowing through the filter of the swimming pool.
Do You Vacuum A Pool On Waste Or Filter
Most often, you realize that pool owners use the Filter setting to vacuum. However, this is so because they do not have much debris or other contaminants in their pool.
If you dont have a high level of contaminants in your pool, using the Filter setting is all you need. This setting allows the vacuumed water to flow through the filter bed before returning to the pool.
When not to filter,
As we pointed out earlier, some pool conditions dont require sending water to the sand filter. Some pools, especially those left unused for a very long time, get infiltrated with algae and debris, forming thick layers on the pool bottom.
If you send such pool water to the filter, it will overload the filter media. Moreover, if algae are shocked with a high level of chlorine dose, the algae dust is likely going to pass through the filter and return to the pool.
Once a flocculent has been used to clear the pool, there is no need to send the pool water to the sand filter.
Its better to vacuum to waste where the water doesnt return to the pool.
Also Check: Landscaping To Hide Pool Equipment
