Saturday, April 20, 2024
HomeCleanHow To Clean Dirt From Bottom Of Pool

How To Clean Dirt From Bottom Of Pool

- Advertisment -

Can I Use Vinegar And Other Household Supplies To Clean An Above Ground Pool Liner

How to clean the dirt off the bottom of Intex pool

White vinegar can be used as an alternative to other chemicals when cleaning your above ground pool liner. Since it is a mild acid, it will help to remove stains and debris from the liner. Like you would with bleach, apply the vinegar with a sponge, put it all over the liner, and then scrub it with a brush. Other household supplies that can be used to clean your pool liner include baking soda and dish soap.

How To Clean A Pool That Is Out Of Balance

If your pool water is out of balance, then your best bet is to drain the pool, vacuum it and refill it. Warren Byington, who co-owns backyard maintenance company Backyard Brothers , recommends refilling your pool with ‘lean, fresh, balanced water, which requires time.’

No vacuum? There is what pool professionals call the ‘drain-and-wash’ method: ‘drain the pool, power-wash it, and fill it anew. Balance the new, fresh water at the outset so it can be maintained thereafter.’

You really should regularly test and rebalance your pool water ‘Otherwise, getting a pool clean and it going off-balance time and time again creates a repetitive dire situation where aggressive measures, such as draining and washing and refilling, are needed.’

Run Your Filter Continuously

Its now time to explore the use of a water filter. Skimming collects larger debris, while filters collect small particles. Your pool water is likely a brown color and filtering will help to clear up the water.

How do filters work? Pool water filters are an effective mechanical process that works by separating water from particles. Water is pulled inside the filter container and goes through the filter medium or a cartridge) inside the filter.

During this process, debris and silt remain in the filter media while the clean water is released back to the pool. Youll need to backwash or clean your filter regularly as it will clog up quickly if you have muddy water.

Tip: Watch the filter gauge for high pressure thats when its time to clean your filter.

Youll need to alternate between vacuuming, skimming and filtering. This process will likely take a few days to clear up the water.

Recommended Reading: How To Get Water Off Pool Cover

When I Vacuum My Pool The Dirt Comes Back In

This is because your filter system isnt powerful enough to filter debris that quickly. If youre dealing with a lot of fine debris thats passing through your filter, turn your filter setting to Waste and bypass the filter completely when you vacuum. Just be sure to fill with freshwater while you vacuum so the water level in your pool doesnt get too low.

How To Clean Dirt From Bottom Of Pool And Take Preventive Measure

How To Clean Dirt From Bottom Of Pool? (4 Super Easy Methods!)

Having a ground floor is really congruent with your living. But the problems arise during the time of its proper maintenance, especially cleaning the bottom of it.

Usually, the best above ground pool vacuum makes this process easier.

But for the bottom of a pool, it can not be a particular solution. Most of the time, pools get dirtier, and water gets cloudy.

The method of cleaning your pool depends on what kind of dirt consists of such as large debris, leaves or acorns, algae or fine particles, sand, or oily substances left in the bottom of the pool.

So cleaning the bottom of the pool is a little challenging also. All types of pools can be cleaned by using the same methods, but you should take care to use the right tools for the pools surface.

Make sure that you have the right supplies.

Recommended Reading: Where To Buy Pool Shock

What You Need To Vacuum Your Pool

If youre looking for some more DIY pool maintenance video tutorials, invest in our Pool Care Video Course by Swim University®. Well show you the proper way to hook up your manual vacuum and vacuum your pool efficiently so you can spend more time swimming.

Clean The Pool Fliter

Learning how to clean a pool filter is one of the most important steps. First, turn on the filter and leave for 2-5 days until the water clears. You may need to clean out the pool filter several times during this step. Keep an eye on the pressure gauge. When it is about 10 psi higher than usual, clean the filter. You’ll need to remove the filter cartridge and clean it with the best garden hose and a spray nozzle. Use a to really get all the gunk out of your filter.

Read Also: How Do I Maintain An Above Ground Pool

Top Two Ways To Remove Mud & Dirt From A Pool

There are two ways to clean the mud out of your pool after rain and get that water clear again:

  • Skimming, Vacuuming, Filtering & Floccing to Remove Mud
  • Partial or Fully Draining to Remove Mud

As always with pools, start with the least drastic method. That is the no drain cleaning method. Here it is.

How Do I Get Dirt Off The Bottom Of My Pool

A couple ways to get dirt off the bottom of your pool

To get rid of dirt from the bottom of your pool, youll need to clean it out. You can use a vacuum or clean water with chlorine pucks. But dont try both at the same time since they wont interact and will just create more work for yourself!

If you dont have or want to use a vacuum, you can scoop the dirt out with a pool net or scrub it off with a pool brush.

Read Also: How Much Do Solar Pool Covers Cost

Removing Algae Without Vacuum

Using the Filter Method

As our team of experts previously stated, pools with filters make it easy to eliminate algae.

To remove algae from swimming pools:

  • Wash the filters thoroughly to avoid debris blockages. Make sure they are turned off.
  • Brush the sides and the pools floor with the right brush type.
  • Turn on the filter to remove the water from the pool.
  • If your pool has no filter, it can be a bit demanding, as you will be more involved. To do this:

  • Sweep the algae to the pools bottom after you have brushed off the sides.
  • Once they settle, swim to the bottom and collect the algae with a dustpan.
  • Dispose of them appropriately.
  • Using Shocks

    To use this method, you need your pool shock product, one pound of calcium hypochlorite, hand gloves, a bucket of water, and your safety goggles.

  • Put on your hand gloves and goggles. Mix some quantity of the shock product and calcium hypochlorite into five to six gallons of water.
  • Pour the mixture on the affected pool parts.
  • Keep the pump constantly running for about eight to twelve hours. Our experts advise that you do this at night for the shock to have enough time to eliminate the algae.
  • If the water appears cloudy after shocking, run the pool for extra long hours.
  • Using Algaecide

    If you have tried all tricks, and your pool still has some algae left, using algaecides is the next best option.

    Backwashing And Rinsing Of The Filter System

    Now start the pool pump again and backwash the sand filter system.

    In my blog article, I explain how you should flush the sand filter system. Just follow the link.

    Heres a rough explanation you can stick to:

  • The pool pump is initially switched off.
  • The multi-valve is moved to the 6 oclock position .
  • Turn the pump on again and wait until the sight glass in the pool pump has clean water.
  • Then the pool pump is switched off again, and the multi-valve is set to rinse.
  • Now start the pool pump. The rinsing must continue until the water in the sight glass is clear.
  • Finally, the multi-valve of the sand filter system is set back to filtration .
  • Regular operation is initiated again when the operating switch of the pool pump is set to automatic mode .
  • If you use a cartridge filter, rinse it off with a garden hose.

    The backwashing and rinsing of the filter system are important so that the filtration remains high and cloudy pool water is prevented.

    Now you can disconnect the hose from the teat and get everything out of the water.

    Tip: Put the vacuum cleaner and the hose in a shady place and not directly in the sun so that they are stored dry.

    Recommended Reading: Does Walmart Sell Pool Sticks

    How To Remove Dirt From The Bottom Of The Pool Without A Vacuum Cleaner

    Even if you dont have a vacuum cleaner like the ones professionals use for most pools, you can still clean your pool. The only difference is that you will be removing the dirt and debris manually, but this can add physical strain.

    If you dont have an automatic pool cleaner, you should be extra careful, so you dont agitate the dirt, which leads to it being suspended in the water.

    Here are some of the steps you must follow to remove dirt from the bottom of your pool without a vacuum cleaner:

    Connect The Vacuum And Hose

    How to Clean Dirt From the Bottom of a Pool

    If the pump is running then switch it off.

    Connect one end of the vacuum hose to the vacuum head and lower it into the pool. Feed the rest down into the pool to remove air from the pool hose. This is known as purging the system.

    Now, either connect the vacuum hose to the skimmer, directly into the outlet or using a skimmer vacuum plate or, if you have one, connect to the dedicated vacuuming inlet at the side of the pool.

    You May Like: How To Use Bleach In Pool

    Connect The Pool Vacuum

    Now go with the pool hose and vacuum cleaner to the appropriate point for the connection this is often the skimmer or a different location in your pool.

    You dont have a vacuum cleaner for your swimming pool? I recommend the Intex pool vacuum set or the Bestway models.

    How to connect the pool vacuum, I explain here:

  • Clamp a long telescopic rod to the pool vacuum cleaner.
  • Now one end of the pool hose is attached to the vacuum cleaner.
  • The pool hose and suction cup must be held underwater to ventilate it in the next step.
  • After the venting process has been completed, the open end of the pool hose is passed through the flap of the skimmer and inserted into the suction tube.
  • The filter system is switched to a manual mode not to interrupt the process.
  • The multi-valve on the sand filter system is now set to filtration .
  • If there is a floor drain, it is closed to increase the suction on the vacuum cleaner.
  • I want to mention here that the return flow in your swimming pool always remains open when vacuuming this is the pipe with the sight glass that leads away from the multi-valve to your pool.

    The next step explains how to clean the pool floor with a vacuum cleaner.

    What Makes A Pool Dirty

    It always seems like pool maintenance is a never-ending job. Even with an excellent filtration system and chemicals from your pool supply store that are great for clearing up a cloudy pool, the bottom and sides of the pool get slimy and covered in both small and large debris over time.

    Why is it vital for you to be consistent with pool cleaning? Your swimming pool gets bombarded with bacteria, dirt, and algae daily. Algae grow in all bodies of water that are not consistently moving.

    Pools are the perfect place for algae to grow, and no matter what you do, you are constantly working to keep it away. Sediment gets in your pool every time it rains.

    Think about the wind carrying dust, decomposing leaves, and droppings from animals that find themselves in the water. Your pool gets dirty from far more than just people.

    Your body also releases fats, ammonia, nitrogen, bacteria, and dirt every time you take a dip. Many different things create buildup, so it is important to know how to clean dirt from bottom of a pool efficiently.

    Read Also: Do It Yourself Pool Kits

    How To Clean Your Own Pool

    This article was co-authored by Rob Litman. Rob Litman is a Landscaper, General Contractor, and the CEO of Vitoli Inc., a landscaping, hardscaping, ecoscaping, and swimming pool design company in Los Angeles, California. With over 20 years of experience in construction, Rob specializes in energy-efficient and drought-tolerant landscaping. He holds General Building Contractor and Registered Pool/Spa Contractor Licenses. In 2007, Rob won House of the Year in Gardena, California.wikiHow marks an article as reader-approved once it receives enough positive feedback. This article received 13 testimonials and 89% of readers who voted found it helpful, earning it our reader-approved status. This article has been viewed 452,618 times.

    If you have your own swimming pool, you may want to save money by cleaning the pool yourself. It takes quite a bit of work to clean a swimming pool and you’ll have to monitor chemical levels at least three times a week. However, it’s worth it to keep your pool clean and safe for use.

    How To Clean A Pool: A Step

    What is the trick to getting very fine sediment out of bottom of pool

    After all, if you’ve budgeted for the cost of an above-ground pool, you’ll know it’s a small investment and pools aren’t exactly low-maintenance backyard additions either, so you will need to be prepared to do the regular cleaning in order to enjoy that summer splash.

    To thoroughly clean above-ground and/or in-ground pools we would recommend picking up the following:

    • A pool net

    You May Like: How To Convert My Chlorine Pool To Salt

    Stick With Slow Movement

    Even when youre brushing the pool sides, make sure you dont move too fast. Doing so will increase the chances of sand and dirt suspending back in the water. To avoid demeaning your own progress, stick to slow brush movements.

    Due to fast movement, the dirt will start moving across the water again and settle elsewhere. Besides, the settlement of a pile of dirt inside the water can take a few minutes. So, try to avoid it.

    How To Clean Dirt From The Bottom Of A Pool

    Even if the water in your pool is clean and sparkling, having dirt on the bottom of the pool just looks awful and unappealing to swim in. So you need to clean it.

    The easiest way to clean dirt from the bottom of a pool is to vacuum the pool using a pool vac. If there is lots of dirt then this is best carried out with the multiport valve on waste otherwise it can be done on the filter setting and backwash afterwards to expel any dirt.

    You can get dirt on the bottom of your pool a number of ways including the wind blowing it in, children throwing it in or if there is a problem with your DE filter if you have one instead of a sand filter.

    I had quite a bit on the bottom of mine recently after replacing some of the pipework to the skimmers which required lifting the paving and digging out around the pipes.

    Also Check: Hot Springs Hot Tub Price

    How To Get Algae Off The Bottom Of Your Pool Using A Pool Vacuum

    A skimmer is an excellent tool for cleaning floating or suspended debris out of your pool. However, pool vacuuming is usually required to remove contaminants on the sides or bottom of the pool.

    Vacuuming algae out of your pool works best after using a flocculant, so the particles bind together and fall to the bottom in large clumps.

    Most pool vacuums connect to the pool filter to run on the normal setting. For light to moderate cleaning, this is fine.

    However, when cleaning up significant algae blooms, it may be necessary to set your pool vacuum to waste or drain mode. The contaminated water gets drained externally and bypasses the pool filter.

    How To Clean Dirt From Bottom Of Pool

    How to Clean Dirt from Bottom of Pool

    You need to follow some different steps for cleaning dirt on your swimming pool bottom.

    • Think carefully about where you place your pool

    How do you decide where you will place your swimming pool? The location you choose is also essential for cleaning your swimming pool because the swimming pool has always been there.

    Such as do not place your pool under or near a large tree.

    And everything that drops from the tree will make dirt at the bottom of the swimming pool.

    Always try to place the pool in a free environment position, where you can often get the sunlight that makes your swimming more enjoyable.

    If you use SunnyTent as it covers your pool after swimming, you can place the pool anywhere or near the trees.

    • Skimming and Brushing

    When you are going to clean your pool, make sure you have the right tools you need.

    Firstly you must use a skimmer with a telescopic pole. You may want to remove the pole to make sure your pool is free of any debris that could contaminate it.

    There is a smell net attached to the telescopic pole, which is an essential pool cleaning tool.

    This net removes leaves and other debris from the surface level of the pool. If you have a leaf skimmer, it will be best to clean the surface of the pool.

    After that you need a pool brush, make sure you have one. Use a brush to clean the sides, stairs, and steps of your pool.

    This should be done every week. And make sure you wash your pool brush from time to time to keep it clean.

    • Set up the vacuum.

    Recommended Reading: How To Add Calcium To Pool

    RELATED ARTICLES
    - Advertisment -

    Most Popular

    - Advertisment -