Kidney Or Irregular Shapes
There are two methods used to calculate the capacity of irregular shapes. First, you can imagine the pool or hot tub as a combination of smaller, regular shapes. Measure these various areas and use the calculations described previously for each square or rectangular area and for each circular area. Add these volumes together to determine the total capacity.
0.45 x x length x average depth x 7.5 = volume
The total of measurement A plus measurement B multiplied by 0.45 multiplied by the length gives you the surface area of the kidney shape. . The rest of the calculations you are now familiar with. Try this volume calculation:
0.45 x x length x average depth x 7.5 = volume
0.45 x 18 ft x 25 ft x 5 ft x 7.5 = 7593.75 gallons
Parts Per Million
One of the most important calculations you will use is parts per million . The amount of solids and liquids in the water is measured in parts per million, as in three parts of chlorine in every one million parts of water, or 3 ppm.
To help, this list shows common terms and their equivalents:
Square foot = 12 inch wide x 12 inch long
Cubic foot = 12 inch wide x 12 inch long x 12 inch high
Cubic yard = 36 inch wide x 36 inch long x 36 inch high
One cubic foot of water contains 7.48 gallons
One cubic foot of water weighs 62.4 pounds
One gallon of water weighs 8.33 pounds
One part per million represents 8.3 pounds of chemical per million gallons of water.
Rectangular Or Square Variable Depth Pools
The Formula: LengthxWidthxAverage-Depthx7.5=Number Of Gallons In Pool.
Square or rectangular pool with variable depths are not quite as easy as the ones with a constant depth, but theyre not all that difficult either. First, the pool owner is going to have to figure out the average depth of the pool by measuring the shallow end depth and then measuring the deep end depth. Add that two figures together and then divide them by two. For example, if the shallow end of the pool is 2-feet and the deep end of the pool is 10-feet, then adding them together and dividing them by 2 will yield you an average depth of 6-feet .
Once you have the average depth of the pool, then measure the length and width of the pool. Now all of these numbers can be plugged into our formula to determine the number of gallons in the pool. Look at our example below to understand it better.
If you have a 12×24 foot square or rectangular pool with a variable depth of six feet, then you would multiple the numbers to come up with the cubic feet of the pool. This would be 12x24x6=1,728 cubic feet. The cubic feet of the pool would then be multiplied by 7.5 to get the gallons of water in the pool. Therefore, the 1,728 cubic feet of our example multiplied by 7.5 would yield a total volume in gallons of 12,960 gallons.
Now That You Know How To Calculate The Number Of Gallons In A Pool:
Take your time and get as close as you can to the actual capacity of your pool in gallons. Do it once and youll always know. If you know who your pool builder was, they may have the digging diagrams or specifications on file, and they can tell you your exact pool water volume.
Once you know exactly how to calculate the number of gallons in a pool, its always a good idea to round up the number to the nearest thousand gallons when engaging in conversation with anyone about chemical additions.
Just an aside its safe to say that the average size of an in ground pool is about 15,000 gallons.
Have fun and good luck!
Don’t Miss: Target Pool Salt
Olympic Swimming Pool Volume
To calculate the Olympic swimming pool volume, you need to know its dimensions. The length of the pool is 50 m, width 25 m, and the depth varies: 2.0 m is the minimum, but 3.0 m is the recommended depth. If you’re not familiar with those metric units, check out this length converter to convert easily the pool size to US or imperial units.
Olympic-size swimming pool contains 2,500,000 L of water, assuming a nominal depth of 2 m. It’s around 550,000 imp gal and 660,000 US gal – if you don’t believe us, you can check it with our volume converter tool, where you’ll find other volume units as well. Try to calculate the Olympic swimming pool volume for a recommended depth of 3 meters – or use the pool calculator to get the answer in the blink of an eye.
Have you ever wondered how many tea- or tablespoons of water can fit into the Olympic swimming pool? We haven’t either. But now you can check it! Awesome, isn’t it?
So On The Back Of Every Single Pool Chemical On Earth There Is Something In Common
And that is for X amount of gallons of water you need to add X amount of the chemical.
And how many gallons of water does your pool hold?
Well, if you dont know were gonna show you how to find out, lets dive in.
All right, if you want the quick answer and the easiest way to find out how many gallons is my pool calculator. and you can enter in your dimensions and your depth, and itll tell you how many gallons of water.
But if you have a very special pool or you want to do it the old-fashioned way were gonna show you every single type of measurement that youre gonna need, were gonna show you how to do the calculations, all the formulas, to find out how muchwater is in your pool.
Okay, so were about to get into some math and before we do that we need to whisk you back to middle school math class to get down some basics, so lets go.
Okay, before we start measuring your pool lets go over a few things well use to calculate your pools volumes.
You May Like: Tibbits Pool Yonkers
How Many Btus Do I Need For A 10000 Gallon Pool
Or approximately 100K BTUs for every 10,000 gallons of pool water. For inground pools less than 20,000 gallons, small gas heaters like the Raypak 206K BTU output are suitable. Pools up to 30,000 gallons should look at the Pentair 300K BTU or higher, and pools over 50,000 gallons should look at the Hayward 500K BTU.
Is 40000 Btu Good For A Patio Heater
Patio heaters that are freestanding have an output of 40,000 BTUs per hour on average. This can heat a room with a circumference of 20 feet, which can accommodate a medium-sized gathering. If you want to heat a room with a circumference of 10 feet or less, get a unit with an output of 20,000 BTUs per hour. This can be used for small gatherings.
Also Check: Aria Pool Cabana Cost
Variable Depth Pools: Square And Rectangular
Length x width x average depth x 7.5 = volume
Length times width gives the surface area of the pool. Multiplying that by the average depth gives the volume in cubic feet. Since there are 7.5 gallons in each cubic foot, multiply the cubic feet of the pool by 7.5 to arrive at the volume of the pool .
Measure the length, width, and average depth of the pool, rounding each measurement off to the nearest foot or percentage of one foot. One inch equals 0.0833 feet. Therefore, multiply the number of inches in your measurements by 0.0833 to get the appropriate percentage of one foot.
Example: 25 ft, 9 in. = 25 ft +
= 25 + 0.75
= 25.75 ft
If the shallow end is 3 feet and the deep end is 9 feet, and assuming the slope of the pool bottom is gradual and even, then the average depth is 6 feet.
Average depth = / 2
Average depth = / 2 = 6 feet.
If most of the pool is only 3 or 4 feet and then a small area drops off suddenly to 10 feet, you will have a different average depth. In such a case, you might want to treat the pool as two parts. Measure the length, width, and average depth of the shallow section, then take the same measurements for the deeper section. Calculate the volume of the shallow section and add that to the volume you calculate for the deeper section.
Length x width x average depth x 7.5 = volume
25.75 ft x 10 ft x 6 ft x 7.5 = 11,587.5 gallons
How Do You Determine The Maximum Occupancy Of A Pool
There are several guidelines and formulas to use when youre trying to determine the maximum occupancy of your swimming pool. For some codes, you would have to consider the recirculation flow rates for each swimmer. For other codes, the maximum occupancy depends on whether you have an outdoor, indoor, deep-end or shallow pool.
Another consideration to think about is the size of any decks which surround your pool or if your pools has diving boards, water slides, and other special equipment. As a pool operator, you must first learn about the health codes for you to use the correct formulas and so that you can adhere to the standards of the pool you have chosen.
Generally, though, if your locale doesnt specify these guidelines, you can use the following:
- One person per 15 ft2 of surface area in parts of the swimming pool which are 5-ft in depth or less.
- One person per 20 ft2 of surface area in parts of the swimming pool which are 5-ft in depth.
- If your pool has a diving board, subtract 300 ft2 from the total value of the surface calculations.
For instance, if the shallow part of your swimming pool is 40 ft x 20 ft, that would be equal to 800 ft2. Using the first guideline, you can calculate the maximum number of persons for this part of the pool:
800 / 15 = 53 people
2900 / 20 = 145 people
Now, all you have to do is add these two values to get the total maximum occupancy of your pool. In our example, this is:
53 + 145 = 198 people
Read Also: How To Heat Above Ground Pool
Important Safety Rules To Follow When Balancing Pool Water
- RULE #1: Always read product label and follow instructions.
- RULE #2: Never mix chemicals .
- RULE #3: Never add water to chemical, always add chemical to water.
This article is a user manual for our pool water balance calculator seen above. It will also teach you what you need to know about proper pool chemistry, and how to maintain a healthy pool. To use our live calculator please click the image above, or This Link.
The first thing you should know about our calculator is that its programmed for residential swimming pools only. Spas and commercial swimming pools require higher levels of chlorine.
The second thing you should know is its only as accurate as your pool volume entered , and other data you supply. It can not give you precise measurements unless it knows how many gallons are in your pool, or what your current chemical levels are. Pool Volume Chart
Dont Miss: Can You Heat An Above Ground Pool
How Many Gallons Of Water Do I Have In My Pool Or Spa
Knowing how many gallons of water you have in your pool and spa is one of the foundational pieces of the puzzle in running your aquatic facility or backyard pool in a safe and healthy way. Even though knowing your pool and spa volumes crucial, it is truly an often overlooked component of operating your pool. Knowing pool and spa volume is crucial for the following reasons:
- Accurate Chemical Adjustments
- Circulation Needs
You May Like: How To Store Pool Towels Outside
Irregularly Shaped Pool Volume
Not all pools are rectangular, square, or round. Some are oval, others are the classic kidney shape, and then some just wiggle all over the place, mimicking natural shorelines.
If you have an irregularly shaped pool, you can still calculate the volume. Youll just have to doyou guessed iteven more math!
The easiest way to calculate an oddly shaped pool is to imagine it broken down into two or more smaller, regularly shaped parts. Try to see smaller, individual squares, rectangles, or circles within the larger, irregular shape.
Once youve mapped them out, measure them, and then use the same formulae that apply to those regular shapes to calculate the volume in each smaller section. Then just add all the volume figures together, and youll have a pretty close approximation of the pools total volume.
Admittedly, this could also be known as the winging it procedure, and youre not going to get a completely accurate volume. If your pool is shaped like a fractal, your best bet is to have a professional take the measurements for you.
Constant Depth Square/rectangle Pool
A Rectangular swimming pool is one of the most common types of swimming pools. If you have
Length x width x depth x 7.5 = volume
You can find the surface area of the pool by multiplying the length and width. Multiplying that by the depth will result in volume in cubic feet. As there are 7.5 gallons in each cubic foot, multiply the cubic feet of the pool by 7.5 to find the volume of the pool.
Recommended Reading: Vdara Hotel Pool
How Do You Size A Heat Pump
heat pumpsTOP 7 Best Pool Heaters Product Review
|Pool Size Imperial|
How Many Gallons Is My Pool
Let’s calculate it with this pool volume calculator!
Choose the shape of your pool. You can select between two types – rectangular/square pool or oval/circle one. Our example is with a standard rectangular pool, so leave the default value.
Enter the dimensions of the swimming pool. Let’s say that the pool is 12 ft wide and 50 ft long. Depth is gradually changing from 4 to 6 feet.
The pool calculator shows the volume of water needed to fill up the pool. In our case, it’s 22,441.57 US gallons.
Our tool is sometimes called the pool size calculator or pool gallon calculator because it works with any units, not just with metric. If we didn’t auto-detect your preferred units, click on meters to change it to gallons.
If your pool doesn’t vary in depth, but is some kind of a fancy shape like bow front or cylinder, check out this aquarium calculator – it has some nice options for different 3D shapes. If the pool of your dreams comes in some custom or eccentric shape, check out the manufacturer’s website.
This calculator finds the total volume of your pool – in reality, you never fill the pool all the way to the brim. Also, you may want to have a look at our other tool associated with submerged objects and their volume and weight – the buoyancy calculator.
Don’t Miss: Pool Salt Calculator
Kidney Or Irregular Shape Pool
Measuring the volume of water in a kidney or irregular-shaped pool is simple if you have the right information. An irregular or kidney-shaped pool has both the circular shapes of a round pool and the elongated shape of a rectangular one. This could make you think it is a very complex task to achieve, but this isnt always the case.
Calculating how many gallons a kidney-shaped pool contains requires the use of three measurements and one formula only. Remember that you have to measure the surface area first before proceeding with the calculations.
Find out more in the next section.
Round Pool Volume Calculator
3.14 x Radius Squared x Average Depth x 7.5 = Volume
What does this mean? Lets explain: 3.14 is referred to as pi, a mathematical constant. Radius is ½ of the round pool diameter and divided by 2. This will get the radius number. Then, multiple that number by itself . For example, If you have 20 Ft round pool, divide by 2 and you will have 10 ft . Now, multiple that number by itself . This will be your Radius Squared number in the equation.
Example: Lets say the average depth of your pool is 8 Ft. and the Radius Squared number is 100. Here is what the formula would look like: 3.14 x 100 x 8 x 7.5 = 18,840 Gallons of Water .
Also Check: Ways To Hide Pool Pump
Pool Volume Calculator For Irregularly Shaped Swimming Pools
There are pools whose shapes cannot be categorized assquare, rectangle, oval or round. They take up any form such as kidney shape,natural shorelines and just any form the owner can come up with. Such pools arecalled irregularly shaped pools.
Supposing you have a pool that is shaped irregularly,obtaining its volume is still possible. You just must do the math. The simplestway to compute an irregularly shaped pool is to picture it in various bits andpieces in regular shapes. Try picturing it as a smaller, separate pool inrectangle, square, or circle within the larger, irregularly shaped pool.
When youve fractioned them in various pieces, measure them and apply the same formula shared above for each corresponding shape. That is, if you have a rectangle fraction, apply the formula for rectangular pools to find the volume in that segment. When you have done this for all parts of the pool, sum the values gotten together and you will have a close approximate value of the irregular pools total volume in gallons.
Honestly, this could be an uncertain method but thereis no way you can accurately measure and compute the exact pool volume of anirregular swimming pool. Supposing your pool is so out of shape, kindly seekprofessional help.